Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

  1. If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM


E241547E01


E226483E09


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly and speakers.

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-15 (WFR+) - N1-1
    Always
    Below 1 Ω
    L142-30 (WFR-) - N1-2
    Always
    Below 1 Ω
    L142-8 (WFL+) - O1-1
    Always
    Below 1 Ω
    L142-23 (WFL-) - O1-2
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-9 (FR+) - I4-1
    Always
    Below 1 Ω
    L142-24 (FR-) - I4-2
    Always
    Below 1 Ω
    L142-14 (FL+) - I5-1
    Always
    Below 1 Ω
    L142-29 (FL-) - I5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-12 (RR+) - P3-1
    Always
    Below 1 Ω
    L142-27 (RR-) - P3-2
    Always
    Below 1 Ω
    L142-11 (RL+) - Q3-1
    Always
    Below 1 Ω
    L142-26 (RL-) - Q3-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-13 (TWR+) - P5-1
    Always
    Below 1 Ω
    L142-28 (TWR-) - P5-2
    Always
    Below 1 Ω
    L142-10 (TWL+) - Q5-1
    Always
    Below 1 Ω
    L142-25 (TWL-) - Q5-2
    Always
    Below 1 Ω

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-15 (WFR+) - Body ground
    Always
    10 kΩ or higher
    L142-30 (WFR-) - Body ground
    Always
    10 kΩ or higher
    L142-8 (WFL+) - Body ground
    Always
    10 kΩ or higher
    L142-23 (WFL-) - Body ground
    Always
    10 kΩ or higher
    L142-9 (FR+) - Body ground
    Always
    10 kΩ or higher
    L142-24 (FR-) - Body ground
    Always
    10 kΩ or higher
    L142-14 (FL+) - Body ground
    Always
    10 kΩ or higher
    L142-29 (FL-) - Body ground
    Always
    10 kΩ or higher
    L142-12 (RR+) - Body ground
    Always
    10 kΩ or higher
    L142-27 (RR-) - Body ground
    Always
    10 kΩ or higher
    L142-11 (RL+) - Body ground
    Always
    10 kΩ or higher
    L142-26 (RL-) - Body ground
    Always
    10 kΩ or higher
    L142-13 (TWR+) - Body ground
    Always
    10 kΩ or higher
    L142-28 (TWR-) - Body ground
    Always
    10 kΩ or higher
    L142-10 (TWL+) - Body ground
    Always
    10 kΩ or higher
    L142-25 (TWL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E21
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N1-1 - N1-2
      Always
      4.6 to 6.6 Ω
      O1-1 - O1-2
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E187205E03
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I4-1 - I4-2
      Always
      3.2 to 4.8 Ω
      I5-1 - I5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT REAR SPEAKER ASSEMBLY


    E219303E22
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P3-1 - P3-2
      Always
      3.2 to 5.2 Ω
      Q3-1 - Q3-2
      Always
      3.2 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E187136E06
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P5-1 - P5-2
      Always
      3.2 to 4.8 Ω
      Q5-1 - Q5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)