Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Driver Side Seat Belt Warning Light does not Operate

for Preparation Click here


DESCRIPTION

When the driver side seat belt is not fastened with the power switch on (IG), the driver side seat belt warning light on the combination meter assembly blinks to inform the driver. The main body ECU (multiplex network body ECU) detects the driver side seat belt condition and sends a signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM


B230297E01


INSPECTION PROCEDURE

NOTICE:
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Seat Buckle SW
    Driver seat belt buckle switch signal/ON or OFF
    ON: Driver seat belt fastened
    OFF: Driver seat belt not fastened
    -

    OK:
    ON or OFF appears on the tester screen according to the driver side seat belt condition.



NG
Go to step 3
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Combination Meter (Combination Meter Assembly) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Driver seat belt warning light
    OFF or ON
    Confirm that the vehicle is stopped with the engine idling.

    OK:
    The driver side seat belt warning light on the combination meter assembly operates normally.



NG
Go to step 6
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)


    B202371E03
  1. Remove the front seat inner belt assembly (driver side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R5-3 (+) - R5-2 (E)*1
    S22-3 (+) - S22-2 (E)*2
    Driver side seat belt unfastened
    Below 1 Ω
    R5-3 (+) - R5-2 (E)*1
    S22-3 (+) - S22-2 (E)*2
    Driver side seat belt fastened
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD
    Text in Illustration 
    *1
    Component without harness connected
    (Front Seat Inner Belt Assembly (Driver Side))
    *2
    for LHD
    *3
    for RHD



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY RH)


    B230298E01
  1. Disconnect the 2B connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-14 (DBKL) - R5-3 (+)*1
    2B-14 (DBKL) - S22-3 (+)*2
    Always
    Below 1 Ω
    2B-14 (DBKL) - Body ground
    Always
    10 kΩ or higher
    R5-2 (E) - Body ground*1
    S22-2 (E) - Body ground*2
    Always
    Below 1 Ω

    1. *1: for LHD
    2. *2: for RHD
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)
    *2
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly (Driver Side))
    *3
    for LHD
    *4
    for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly (Click here).


    B230299E01

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    This inspection is to check the wire harness in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-18 (DBKL) - 2B-14 (DBKL)
    Always
    Below 1 Ω
    2B-14 (DBKL) - Body ground
    Always
    10 kΩ or higher


    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *2
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

6.REPLACE NO. 5 METER CIRCUIT PLATE
  1. Replace the No. 5 meter circuit plate (Click here).


NEXT


7.CHECK DRIVER SIDE SEAT BELT WARNING LIGHT
  1. Check the driver side seat belt warning light (Click here).

    OK:
    The driver side seat belt warning light operates normally.



NG
Go to step 8
OK

END (NO. 5 METER CIRCUIT PLATE WAS DEFECTIVE) 

8.REPLACE NO. 2 METER CIRCUIT PLATE
  1. Replace the No. 2 meter circuit plate (Click here).


NEXT


9.CHECK DRIVER SIDE SEAT BELT WARNING LIGHT
  1. Check the driver side seat belt warning light (Click here).

    OK:
    The driver side seat belt warning light operates normally.



NG
REPLACE NO. 3 METER CIRCUIT PLATE (Click here)
OK

END (NO. 2 METER CIRCUIT PLATE WAS DEFECTIVE)