CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (RHD Models) |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. |
|


| 1.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - CAN NO. 1 J/C) |
Turn the power switch off.
![]() |
Disconnect the CAN No. 2 junction connector.
| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *2 | to CAN No. 1 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-6 (CANH) - L95-17 (CANL) | Power switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 2.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-9 (CANH) - L95-20 (CANL) | Power switch off | 108 to 132 Ω |
| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *2 | to ECM |
|
| ||||
| OK | |
| 3.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - DLC3) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-4 (CANH) - L95-15 (CANL) | Power switch off | 1 MΩ or higher |
| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *2 | to DLC3 |
|
| ||||
| OK | |
| 4.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - SKID CONTROL ECU) |
![]() |
Disconnect the skid control ECU (brake booster with master cylinder) connector.
| *1 | Front view of wire harness connector (to Skid Control ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-3 (CANH) - L95-14 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *3 | to Skid Control ECU |
|
| ||||
| OK | |
| 5.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - NAVIGATION ECU) |
for HDD:
![]() |
Disconnect the navigation ECU connector.
| *1 | Front view of wire harness connector (to Navigation ECU) |
for DVD:
![]() |
Disconnect the navigation ECU connector.
| *1 | Front view of wire harness connector (to Navigation ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-5(CANH) - L95-16(CANL) | Power switch off | 1 MΩ or higher |
| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *2 | to Navigation ECU |
|
| ||||
| OK | |
| 6.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - STEERING ANGLE SENSOR) |
![]() |
Disconnect the steering angle sensor connector.
| *1 | Front view of wire harness connector (to Steering Angle Sensor) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-1 (CANH) - L95-12 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *3 | to Steering Angle Sensor |
|
| ||||
| OK | |
| 7.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - POWER STEERING ECU) |
![]() |
Disconnect the power steering ECU connector.
| *1 | Front view of wire harness connector (to Power Steering ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-2 (CANH) - L95-13 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *3 | to Power Steering ECU |
|
| ||||
| OK | |
| 8.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C - CERTIFICATION ECU) |
![]() |
Disconnect the certification ECU connector.
| *1 | Front view of wire harness connector (to Certification ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-7 (CANH) - L95-18 (CANL) | Power switch off | 108 to 132 Ω |
| *2 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *3 | to Certification ECU |
|
| ||||
| OK | |
| 9.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 J/C) |
Reconnect the CAN No. 2 junction connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L61-6 (CANH) - L61-14 (CANL) | Power switch off | 54 to 69 Ω |
| *1 | DLC3 |
|
| ||||
| OK | |
| 10.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR) |
![]() |
Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
| *1 | DLC3 |
While observing the resistance value shown on the ohmmeter, reconnect each ECU and sensor connector until the resistance becomes abnormal (below 54 Ω).
| NEXT | ||
| ||
| 11.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C - CAN NO. 2 J/C) |
Reconnect the CAN No. 2 junction connector.
![]() |
Disconnect the CAN No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-3 (CANH) - L94-14 (CANL) | Power switch off | 108 to 132 Ω |
| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *2 | to CAN No. 2 Junction Connector |
|
| ||||
| OK | |
| 12.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C - COMBINATION METER) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-1 (CANH) - L94-12 (CANL) | Power switch off | 108 to 132 Ω |
| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *2 | to Combination Meter |
|
| ||||
| OK | |
| 13.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C - POWER MANAGEMENT CONTROL ECU) |
![]() |
Disconnect the power management control ECU connector.
| *1 | Rear view of wire harness connector (to Power Management Control ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-6 (CANH) - L94-17 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *3 | to Power Management Control ECU |
|
| ||||
| OK | |
| 14.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C - TRANSMISSION CONTROL ECU) |
![]() |
Disconnect the transmission control ECU connector.
| *1 | Front view of wire harness connector (to Transmission Control ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-7 (CANH) - L94-18 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *3 | to Transmission Control ECU |
|
| ||||
| OK | |
| 15.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C - YAW RATE SENSOR) |
![]() |
Disconnect the yaw rate sensor connector.
| *1 | Front view of wire harness connector (to Yaw Rate Sensor) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-4 (CANH) - L94-15 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *3 | to Yaw Rate Sensor |
|
| ||||
| OK | |
| 16.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C - CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Disconnect the center airbag sensor assembly connector.
| *1 | Front view of wire harness connector (to Center Airbag Sensor Assembly) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-5 (CANH) - L94-16 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *3 | to Center Airbag Sensor Assembly |
|
| ||||
| OK | |
| 17.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C - MAIN BODY ECU) |
![]() |
Disconnect the main body ECU connector.
| *1 | Front view of wire harness connector (to Main Body ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-2 (CANH) - L94-13 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *3 | to Main Body ECU |
|
| ||||
| OK | |
| 18.CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 J/C) |
Reconnect the CAN No. 1 junction connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L61-6 (CANH) - L61-14 (CANL) | Power switch off | 54 to 69 Ω |
| *1 | DLC3 |
|
| ||||
| OK | |
| 19.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR) |
![]() |
Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
| *1 | DLC3 |
While observing the resistance value shown on the ohmmeter, reconnect each ECU and sensor connector until the resistance becomes abnormal (below 54 Ω).
| NEXT | ||
| ||
| 20.CHECK FOR SHORT IN CAN BUS WIRES (ECM) |
![]() |
Disconnect the ECM connector.
| *1 | Front view of wire harness connector (to ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L95-9 (CANH) - L95-20 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *3 | to ECM |
|
| ||||
| OK | ||
| ||
| 21.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER) |
![]() |
Disconnect the combination meter connector.
| *1 | Front view of wire harness connector (to Combination Meter) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-1 (CANH) - L94-12 (CANL) | Power switch off | 1 MΩ or higher |
| *2 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *3 | to Combination Meter |
|
| ||||
| OK | ||
| ||