Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION


Before October, 2010
The R/F, TEMP UP (+), and TEMP DOWN (-) switches are located on the steering pad switch assembly. The resistance of the steering pad switch assembly changes in accordance with switch operation. The A/C control assembly outputs voltage to the steering pad switch assembly and reads voltage changes due to the resistance changes that result from switch operation.

HINT:
If there is an open in the circuit, the A/C system cannot be operated by the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the A/C control assembly cannot be operated by the steering pad switch assembly, and the A/C control assembly will not be able to function correctly.


From October, 2010
The R/F, TEMP UP (+), and TEMP DOWN (-) switches are located on the steering pad switch RH. The resistance of the steering pad switch RH changes in accordance with switch operation. The A/C control assembly outputs voltage to the steering pad switch RH and reads voltage changes due to the resistance changes that result from switch operation.

HINT:
If there is an open in the circuit, the A/C system cannot be operated by the steering pad switch RH.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the A/C control assembly cannot be operated by the steering pad switch RH, and the A/C control assembly will not be able to function correctly.


WIRING DIAGRAM


Before October, 2010

E194145E08


From October, 2010

E194145E06


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.INSPECT A/C CONTROL ASSEMBLY


    E168579E32
  1. Disconnect the connector from the spiral with sensor cable sub-assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L52-10 (AC1) - Body ground
    Power switch off
    Below 1 V
    L52-10 (AC1) - Body ground
    Power switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)



NG
Go to step 8
OK


2.CHECK HARNESS AND CONNECTOR


    E168561E54
  1. Disconnect the connector from the navigation receiver assembly.



    E168561E52
  1. Disconnect the connector from the radio receiver assembly.



    E168579E34
  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L109-6 (SWG) - L52-4 (EAU)*4
    Always
    Below 1 Ω
    L41-6 (SWG) - L52-4 (EAU)*5
    Always
    Below 1 Ω
    L50-6 (SWG) - L52-4 (EAU)*6
    Always
    Below 1 Ω
    L52-4 (EAU) - Body ground*7
    Always
    Below 1 Ω
    L109-6 (SWG) - Body ground*4
    Always
    10 kΩ or higher
    L41-6 (SWG) - Body ground*5
    Always
    10 kΩ or higher
    L50-6 (SWG) - Body ground*6
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *3
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)
    1. *4: w/ Navigation System (for HDD)
    2. *5: w/ Navigation System (for DVD)
    3. *6: w/o Navigation System
    4. *7: w/o Radio Receiver



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH


  1. Before October, 2010



    1. Disconnect the connector from the steering pad switch assembly.


      E187115E02

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      z9-3 (AC1) - z9-8 (EAU)
      No switch pushed
      95 to 105 kΩ
      z9-3 (AC1) - z9-8 (EAU)
      R/F switch pushed
      312 to 345 Ω
      z9-3 (AC1) - z9-8 (EAU)
      TEMP+ switch pushed
      950 to 1050 Ω
      z9-3 (AC1) - z9-8 (EAU)
      TEMP- switch pushed
      2954 to 3265 Ω


      Text in Illustration 
      *1
      Component without harness connected
      (Steering Pad Switch Assembly)
      *2
      R/F Switch
      *3
      TEMP+ Switch
      *4
      TEMP- Switch



  1. From October, 2010



    1. Disconnect the connector from the steering pad switch RH.


      E256404E03

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      z9-3 (AC1) - z9-8 (EAU)
      No switch pushed
      95 to 105 kΩ
      z9-3 (AC1) - z9-8 (EAU)
      R/F switch pushed
      312 to 345 Ω
      z9-3 (AC1) - z9-8 (EAU)
      TEMP+ switch pushed
      950 to 1050 Ω
      z9-3 (AC1) - z9-8 (EAU)
      TEMP- switch pushed
      2954 to 3265 Ω


      Text in Illustration 
      *1
      Component without harness connected
      (Steering Pad Switch RH)
      *2
      R/F Switch
      *3
      TEMP+ Switch
      *4
      TEMP- Switch

      Result:
      Result
      Proceed to
      OK
      A
      NG (Before October, 2010)
      B
      NG (From October, 2010)
      C



B
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)

C
REPLACE STEERING PAD SWITCH RH (Click here)
A


4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    E187114E06
  1. Disconnect the connector from the spiral with sensor cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L52-10 (AC1) - z9-3 (AC1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    L52-4 (EAU) - z9-8 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)
    3. The spiral cable makes a maximum of approximately 5 rotations.

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral with Sensor Cable Sub-assembly)
    *2
    Steering Pad Switch Side
    *3
    Vehicle Side



NG
REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (Click here)
OK


5.CONFIRM MODEL

Result:
Result
Proceed to
w/ Navigation System
A
w/o Navigation System
B
w/o Radio Receiver
C



B
Go to step 7

C
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


6.REPLACE NAVIGATION RECEIVER ASSEMBLY
  1. Replace the navigation receiver assembly with a known good one and check if the same problem occurs again (Click here).

    OK:
    Same problem does not occur.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (NAVIGATION RECEIVER ASSEMBLY WAS DEFECTIVE) 

7.REPLACE RADIO RECEIVER ASSEMBLY
  1. Replace the radio receiver assembly with a known good one and check if the same problem occurs again (Click here).

    OK:
    Same problem does not occur.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (RADIO RECEIVER ASSEMBLY WAS DEFECTIVE) 

8.CHECK HARNESS AND CONNECTOR (A/C CONTROL ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)


    E167399E30
  1. Disconnect the connector from the A/C control assembly.



    E168579E35
  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L20-3 (SWO) - L52-10 (AC1)
    Always
    Below 1 Ω
    L20-3 (SWO) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to A/C Control Assembly)
    *2
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C CONTROL ASSEMBLY (Click here)