CAN COMMUNICATION SYSTEM > Open in CAN Main Bus Line (LHD Models) |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher. |
|

| 1.CHECK FOR OPEN IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
Turn the power switch off.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L61-6 (CANH) - L61-14 (CANL) | Power switch off | 108 to 132 Ω |
| *1 | DLC3 |
|
| ||||
| OK | |
| 2.CHECK FOR OPEN IN CAN BUS WIRE (ECM) |
![]() |
Disconnect the ECM connector.
| *1 | Front view of wire harness connector (to ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A57-13 (CANH) - A57-5 (CANL) | Power switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 3.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER) |
Reconnect the ECM connector.
![]() |
Disconnect the combination meter connector.
| *1 | Front view of wire harness connector (to Combination Meter) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L27-10 (CANH) - L27-11 (CANL) | Power switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 4.CHECK FOR OPEN IN CAN BUS WIRE (CAN NO. 1 J/C) |
Reconnect the combination meter connector.
![]() |
Disconnect the CAN No. 1 junction connector.
| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *2 | to Combination Meter |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-1 (CANH) - F94-12 (CANL) | Power switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 5.CHECK FOR OPEN IN CAN BUS WIRE (CAN NO. 1 J/C - CAN NO. 2 J/C) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L94-7 (CANH) - L94-18 (CANL) | Power switch off | 108 to 132 Ω |
| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *2 | to CAN No. 2 Junction Connector |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR OPEN IN CAN BUS WIRE (CAN NO. 2 J/C) |
Reconnect the CAN No. 1 junction connector.
![]() |
Disconnect the CAN No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Connected to |
| L95-3 (CANH) - L95-14 (CANL) | Power switch off | 108 to 132 Ω | CAN No. 1 junction connector |
| L95-9 (CANH) - L95-20 (CANL) | Power switch off | 108 to 132 Ω | ECM |
| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *2 | to CAN No. 1 Junction Connector |
| *3 | to ECM |
| Result | Proceed to |
| OK | A |
| NG (to ECM main wire) | B |
| NG (to CAN No. 1 junction connector main wire) | C |
|
| ||||
|
| ||||
| A | ||
| ||