Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > No Answer-Back

for Preparation Click here


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function(s) does not operate. In such cases, the hazard warning light and wireless door lock buzzer signals output from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM


B226587E04


INSPECTION PROCEDURE

NOTICE:
Troubleshooting should be started after confirming that the customize status of the answer-back function has been switched on.

1.READ VALUE USING INTELLIGENT TESTER (ANSWER-BACK OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Utility / Customize.

  1. Select the setting by referring to the table below.


Wireless Door Lock Control System 
Display (item)
Default
Function
Setting
Hazard Answer Back
ON
When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
ON or OFF
Wireless Buzzer Resp*
ON
Wireless door lock buzzer response on or off
ON or OFF
*: for Australia

Result:
Result
Proceed to
Both items are on.
A
Either item is off.
B



B
PERFORM CUSTOMIZE FUNCTION (ANSWER-BACK FUNCTION) (Click here)
A


2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check the wireless door lock control function by the electrical key transmitter.


Result:

Result
Proceed to
Wireless door lock/unlock operates normally.
A
Wireless door lock/unlock does not operate normally.
B



B
GO TO ENTRY AND START SYSTEM (Click here)
A


3.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos
    Front right side lock position switch signal/LOCK or UNLOCK
    LOCK: Front right side door locked
    UNLOCK: Front right side door unlocked
    -
    FL Door Lock Pos
    Front left side door lock position switch signal/LOCK or UNLOCK
    LOCK: Front left side door locked
    UNLOCK: Front left side door unlocked
    -
    RR-Door Lock Pos SW
    Rear right side door lock position switch signal/ON or OFF
    ON: Rear right side door unlocked
    OFF: Rear right side door locked
    -
    RL-Door Lock Pos SW
    Rear left side door lock position switch signal/ON or OFF
    ON: Rear left side door unlocked
    OFF: Rear left side door locked
    -

    OK:
    The intelligent tester should display as shown in the table according to door lock operation.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for Front RH Side)
    B
    NG (for Front LH Side)
    C
    NG (for Rear RH Side)
    D
    NG (for Rear LH Side)
    E



B
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)

C
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)

D
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)

E
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)
A


4.CHECK WIRELESS ANSWER-BACK OPERATION
  1. Check the wireless answer-back operation by wireless door lock control function.

    Result:

    Result
    Proceed to
    Only hazard warning light answer-back does not occur.
    A
    Only wireless door lock buzzer answer-back does not occur. (for Australia)
    B



B
Go to step 8
A


5.CHECK HAZARD WARNING LIGHT OPERATION
  1. Check that the hazard warning lights flash continuously when the hazard warning signal switch is pressed.

    OK:
    Hazard warning lights flash continuously.



NG
GO TO LIGHTING SYSTEM (Click here)
OK


6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Hazard
    Turn signal flasher relay
    ON/OFF
    Observe headlights and rear combination lights for correct operation

    Result:

    Result
    Proceed to
    Turn signal flasher relay does not turn on/off.
    A
    Turn signal flasher relay turns on/off.
    B



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
A


7.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the L55 turn signal flasher assembly and L7 main body ECU (multiplex network body ECU) connectors.



    B220281E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L55-8 (HAZ) - L7-3 (HAZ)
    Always
    Below 1 Ω
    L55-8 (HAZ) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Turn Signal Flasher Assembly)
    *2
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Wireless Buzzer
    Turns the wireless door lock buzzer
    ON/OFF
    -

    Result:

    Result
    Proceed to
    Wireless door lock buzzer does not turn on/off.
    A
    Wireless door lock buzzer turns on/off.
    B



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
A


9.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - DRIVER SIDE JUNCTION BLOCK)
  1. Disconnect the A33 wireless door lock buzzer and 2C driver side junction block assembly connectors.



    B217456E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A33-1 (B) - 2C-23 (BZR)
    Always
    Below 1 Ω
    A33-2 (E) - Body ground
    Always
    Below 1 Ω
    A33-1 (B) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Wireless Door Lock Buzzer)
    *2
    Front view of wire harness connector
    (to Driver Side Junction Block Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY


  1. Remove the driver side junction block assembly (Click here).


    B217457E06


    Text in Illustration 
    *1
    Component without harness connected
    (Driver Side Junction Block Assembly)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-23 (BZR) - A-21 (BZR)
    Always
    Below 1 Ω



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
OK


11.REPLACE WIRELESS DOOR LOCK BUZZER
  1. Temporarily replace the wireless door lock buzzer with a new one (Click here).


NEXT


12.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
  1. Check the operation of the wireless answer-back function.

    OK:
    Wireless answer-back function operates normally.



NG
Go to step 13
OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE) 

13.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Temporarily replace the main body ECU (multiplex network body ECU) with a new one (Click here).


NEXT


14.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
  1. Check the operation of the wireless function.

    OK:
    Wireless function operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)