AUDIO AND VISUAL SYSTEM > Microphone Circuit between Microphone and Radio Receiver |

| 1.INSPECT RADIO RECEIVER ASSEMBLY |
![]() |
Disconnect the radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L45-3 (MACC) - Body ground | Power switch on (IG) | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L45-6 (SGND) - Body ground | Always | Below 1 Ω |
| L45-5 (MIN-) - Body ground | Always | Below 1 Ω |
| *1 | Component without harness connected (Radio Receiver Assembly) |
|
| ||||
| OK | |
| 2.CONFIRM MODEL |
Choose the model to be inspected.
| Model | Proceed to |
| w/o Sliding Roof | A |
| w/ Sliding Roof | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RADIO RECEIVER ASSEMBLY) |
![]() |
Disconnect the radio receiver assembly connector.
![]() |
Disconnect the map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L45-1 (SNS2) - U3-2 (SNS2) | Always | Below 1 Ω |
| L45-3 (MACC) - U3-5 (MACC) | Always | Below 1 Ω |
| L45-2 (MIN+) - U3-4 (MCO+) | Always | Below 1 Ω |
| L45-5 (MIN-) - U3-3 (MCO-) | Always | Below 1 Ω |
| L45-1 (SNS2) - Body ground | Always | 10 kΩ or higher |
| L45-3 (MACC) - Body ground | Always | 10 kΩ or higher |
| L45-2 (MIN+) - Body ground | Always | 10 kΩ or higher |
| L45-5 (MIN-) - Body ground | Always | 10 kΩ or higher |
| L45-6 (SGND) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Radio Receiver Assembly) |
| *2 | Front view of wire harness connector (to Map Light Assembly) |
|
| ||||
| OK | |
| 4.INSPECT MAP LIGHT ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U3-2 (SNS2) - U3-3 (MCO-) | Always | Below 1 Ω |
| *1 | Component without harness connected (Map Light Assembly) |
|
| ||||
| OK | |
| 5.INSPECT MAP LIGHT ASSEMBLY |
Reconnect the radio receiver assembly connector.
![]() |
Reconnect the map light assembly connector.
Turn the power switch on (ACC).
Connect an oscilloscope to terminals U3-4 (MCO+) and U3-3 (MCO-) of the map light assembly connector.
Check the waveform of the telephone microphone assembly using an oscilloscope.
| Result | Proceed to |
| A waveform synchronized with the voice input to the telephone microphone assembly is output | A |
| A waveform synchronized with the voice input to the telephone microphone assembly is not output | B |
| *1 | Component with harness connected (Map Light Assembly) |
|
| ||||
| A | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RADIO RECEIVER ASSEMBLY) |
![]() |
Disconnect the radio receiver assembly connector.
![]() |
Disconnect the map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L45-1 (SNS2) - U13-3 (SNS2) | Always | Below 1 Ω |
| L45-3 (MACC) - U13-6 (MACC) | Always | Below 1 Ω |
| L45-2 (MIN+) - U13-5 (MCO+) | Always | Below 1 Ω |
| L45-5 (MIN-) - U13-4 (MCO-) | Always | Below 1 Ω |
| L45-1 (SNS2) - Body ground | Always | 10 kΩ or higher |
| L45-3 (MACC) - Body ground | Always | 10 kΩ or higher |
| L45-2 (MIN+) - Body ground | Always | 10 kΩ or higher |
| L45-5 (MIN-) - Body ground | Always | 10 kΩ or higher |
| L45-6 (SGND) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Radio Receiver Assembly) |
| *2 | Front view of wire harness connector (to Map Light Assembly) |
|
| ||||
| OK | |
| 7.INSPECT MAP LIGHT ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U13-3 (SNS2) - U13-4 (MCO-) | Always | Below 1 Ω |
| *1 | Component without harness connected (Map Light Assembly) |
|
| ||||
| OK | |
| 8.INSPECT MAP LIGHT ASSEMBLY |
Reconnect the radio receiver assembly connector.
![]() |
Reconnect the map light assembly connector.
Turn the power switch on (ACC).
Connect an oscilloscope to terminals U13-5 (MCO+) and U13-4 (MCO-) of the map light assembly connector.
Check the waveform of the telephone microphone assembly using an oscilloscope.
| Result | Proceed to |
| A waveform synchronized with the voice input to the telephone microphone assembly is output | A |
| A waveform synchronized with the voice input to the telephone microphone assembly is not output | B |
| *1 | Component with harness connected (Map Light Assembly) |
|
| ||||
| A | ||
| ||
| 9.REPLACE TELEPHONE MICROPHONE ASSEMBLY |
Replace the telephone microphone assembly .
Check if the same malfunction recurs.
| Result | Proceed to |
| Malfunction does not recur (returns to normal) | A |
| Malfunction recurs | B |
|
| ||||
| A | ||
| ||