INTELLIGENT PARKING ASSIST SYSTEM > CALIBRATION |
| ADJUST INTELLIGENT PARKING ASSIST SYSTEM |
This intelligent parking assist system can be set from the diagnostic screen of the navigation receiver assembly.
If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.
| Part Name | Operation | Adjustment Item | Proceed to |
| Spiral with sensor cable sub-assembly |
| Steering angle neutral point |
Click here
|
| Steering angle setting |
Click here
| ||
| Spiral with sensor cable sub-assembly | Replacement | Steering angle neutral point |
Click here
|
| Steering angle setting |
Click here
| ||
| Parking assist ECU | Replacement | Parking assist ECU initialization | Step 2 |
| Suspension, tires, etc. | The vehicle height changes because of suspension or tire replacement | Height control sensor vehicle height difference (Height set) | Step 3 |
| Rear television camera optical axis (Camera position setting) | Step 4 | ||
| Rear television camera assembly |
| Rear television camera optical axis (Camera position setting) | Step 4 |
| Rear height control sensor sub-assembly RH |
| Height control sensor vehicle height difference (Height set) | Step 3 |
| Rear television camera optical axis (Camera position setting) | Step 4 | ||
| Lighting system initialization |
Click here
| ||
| Rear bumper cover |
| Rear bumper position (BUMPER) | Step 5 |
| PARKING ASSIST ECU INITIALIZATION |
Preparation for adjustment
Park the vehicle on the flat place with the steering wheel centered.
Adjust the tire pressure to the specification.
![]() |
Measure the distance A between the ground and the edge of a rear wheel arch.
Calculate the difference between the distance A and the standard height below.
Set a target bar for optical axis adjustment of the rear television camera.

| A | B | C | D | E | F |
| 1100 mm (3.61 ft.) | 1600 mm (5.25 ft.) | 30 mm (1.18 in.) | 100 mm (3.94 in.) | 500 mm (1.64 ft.) | 30 mm (1.18 in.) |
| *1 | Target Bar for Camera Adjustment | *2 | Vehicle Center |
| *3 | Bumper Edge | *4 | Front Side |
Start diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" on the Service Menu screen.
![]() |
Select "Camera Setting" on the Function Check/Setting screen.
![]() |
Check that "CHK" (red) is not displayed on the SIGNAL CHECK screen.
HEIGHT SET
![]() |
Select the indicator "A" for "HT INIT" on the SIGNAL CHECK screen.
![]() |
Press "UP" and "DOWN" to input the calculated difference.
After inputting the calculated difference, select "OK". The height control sensor vehicle height difference setting will be recorded.
Select "NEXT" on the SIGNAL CHECK screen.
![]() |
INDIVIDUAL SETTING
Select the "EPS LES" on the INDIVIDUAL SETTING screen.
Select "NEXT" on the INDIVIDUAL SETTING screen.
![]() |
CAMERA POSITION SETTING (ROLL ANGLE ADJUSTMENT)
Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
Select "NEXT" on the CAMERA POSITION SETTING (ROLL ANGLE ADJUSTMENT) screen.
CAMERA POSITION SETTING (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT)
![]() ![]() |
By pressing the left and right, and up and down switches, move the parallelograms (A) vertically and horizontally so that the corners of the target bars (C) and the corners of the parallelograms (A) match.

Select "NEXT" on the CAMERA POSITION SETTING (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT) screen.
![]() |
BUMPER (SIMULTANEOUS ADJUSTMENT)
By pressing the left and right, up and down and A and B switches, move the bumper reference lines vertically and horizontally or rotate them so that the bumper reference lines overlap or contact the bumper edge line.
When the bumper reference lines and bumper edge line overlap or contact each other, select "NEXT".
LEFT BUMPER
![]() |
By pressing the left and right, up and down and A and B switches, move the left bumper reference line vertically and horizontally or rotate it so that the bumper reference lines overlap or contact the bumper edge line.
Select "NEXT" on the LEFT BUMPER screen.
RIGHT BUMPER
![]() |
By pressing the left and right, up and down and A and B switches, move the right bumper reference line vertically and horizontally or rotate it so that the bumper reference lines overlap or contact the bumper edge line.
Select "NEXT" on the RIGHT BUMPER screen.
VERIFY MODE
![]() |
Check that line A (indicating 1100 mm forward from the bumper edge) and the target bars are nearly overlapping and that the bumper reference lines and bumper edge line are nearly overlapping. With the steering wheel centered, check that the predicted path line is straight (overlapping the vehicle width extension lines).
Selecting "NEXT" on the VERIFY MODE screen will be completed the camera aiming adjustment.
STEERING ANGLE SETTING
![]() |
Perform the STEERING CENTER MEMORIZE operation.
Perform the MAX STEERING ANGLE MEMORIZE operation.
Finish diagnostic mode (Click here).
Confirm steering angle adjustment.
Check on the intelligent parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.
| HEIGHT CONTROL SENSOR VEHICLE HEIGHT DIFFERENCE SETTING (HEIGHT SET) |
Preparation for adjustment
Adjust the tire pressure to the specification.
![]() |
Measure the distance A between the ground and the edge of a rear wheel arch.
Calculate the difference between the distance A and the standard height below.
Start diagnostic mode.
![]() |
Select "Function Check/Setting" on the Service Menu screen.
![]() |
Select "Camera Setting" on the Function Check/Setting screen.
![]() |
Select "BACK CAMERA SETTING" on the MODE SETTING screen.
![]() |
Select the indicator "A" for "HT INIT" on the SIGNAL CHECK screen.
HEIGHT SET
![]() |
Press "UP" and "DOWN" to input the calculated difference.
After inputting the calculated difference, select "OK". The height control sensor vehicle height difference setting will be recorded.
Finish diagnostic mode.
| REAR TELEVISION CAMERA OPTICAL AXIS ADJUSTMENT (CAMERA POSITION SETTING) |
Preparation for adjustment
Park the vehicle with the steering wheel centered.
Adjust the tire pressure to the specification.
Set a target bar for optical axis adjustment of the rear television camera.

| A | B | C | D | E | F |
| 1100 mm (3.61 ft.) | 1600 mm (5.25 ft.) | 30 mm (1.18 in.) | 100 mm (3.94 in.) | 500 mm (1.64 ft.) | 30 mm (1.18 in.) |
| *1 | Target Bar for Camera Adjustment | *2 | Vehicle Center |
| *3 | Bumper Edge | *4 | Front Side |
Start diagnostic mode.
![]() |
Select "Function Check/Setting" on the "Service Menu" screen.
![]() |
Select "Camera Setting" on the Function Check/Setting screen.
![]() |
Select "BACK CAMERA SETTING" on the MODE SETTING screen.
![]() |
Select "NEXT" on the SIGNAL CHECK screen.
![]() |
INDIVIDUAL SETTING
Select the "EPS LES" on the INDIVIDUAL SETTING screen.
Select "NEXT" on the INDIVIDUAL SETTING screen.
![]() |
CAMERA POSITION SETTING (ROLL ANGLE ADJUSTMENT)
Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
Select "NEXT" on the CAMERA POSITION SETTING (ROLL ANGLE ADJUSTMENT) screen.
CAMERA POSITION SETTING (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT)
![]() ![]() |
By pressing the left and right, and up and down switches, move the parallelograms (A) vertically and horizontally so that the corners of the target bars (C) and the corners of the parallelograms (A) match.

Select "NEXT" on the CAMERA POSITION SETTING (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT) screen.
![]() |
BUMPER (SIMULTANEOUS ADJUSTMENT)
By pressing the left and right, up and down and A and B switches, move the bumper reference lines vertically and horizontally or rotate them so that the bumper reference lines overlap or contact the bumper edge line.
When the bumper reference lines and bumper edge line overlap or contact each other, select "NEXT".
LEFT BUMPER
![]() |
By pressing the left and right, up and down and A and B switches, move the left bumper reference line vertically and horizontally or rotate it so that the bumper reference lines overlap or contact the bumper edge line.
Select "NEXT" on the LEFT BUMPER screen.
RIGHT BUMPER
![]() |
By pressing the left and right, up and down and A and B switches, move the right bumper reference line vertically and horizontally or rotate it so that the bumper reference lines overlap or contact the bumper edge line.
Select "NEXT" on the RIGHT BUMPER screen.
VERIFY MODE
![]() |
Check that line A (indicating 1100 mm forward from the bumper edge) and the target bars are nearly overlapping and that the bumper reference lines and bumper edge line are nearly overlapping. With the steering wheel centered, check that the predicted path line is straight (overlapping the vehicle width extension lines).
Selecting "NEXT" on the VERIFY MODE screen will be completed the camera aiming adjustment.
Finish diagnostic mode.
| BUMPER POSITION SETTING |
Start diagnostic mode.
![]() |
Select "Function Check/Setting" on the "Service Menu" screen.
![]() |
Select "Camera Setting" on the Function Check/Setting screen.
![]() |
Select "BACK CAMERA SETTING" on the MODE SETTING screen.
![]() |
Select "NEXT" on the SIGNAL CHECK screen.
![]() |
INDIVIDUAL SETTING
Select the "EPS LES" on the INDIVIDUAL SETTING screen.
Select "NEXT" on the INDIVIDUAL SETTING screen.
![]() |
CAMERA POSITION SETTING (ROLL ANGLE ADJUSTMENT)
Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
Select "NEXT" on the CAMERA POSITION SETTING (ROLL ANGLE ADJUSTMENT) screen.
CAMERA POSITION SETTING (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT)
![]() |
By pressing the left and right, and up and down switches, move the parallelograms (A) vertically and horizontally so that the corners of the target bars (C) and the corners of the parallelograms (A) match.
Select "NEXT" on the CAMERA POSITION SETTING (VERTICAL AND HORIZONTAL POSITION ADJUSTMENT) screen.
![]() |
BUMPER (SIMULTANEOUS ADJUSTMENT)
By pressing the left and right, up and down and A and B switches, move the bumper reference lines vertically and horizontally or rotate them so that the bumper reference lines overlap or contact the bumper edge line.
When the bumper reference lines and bumper edge line overlap or contact each other, select "NEXT".
LEFT BUMPER
![]() |
By pressing the left and right, up and down and A and B switches, move the left bumper reference line vertically and horizontally or rotate it so that the bumper reference lines overlap or contact the bumper edge line.
Select "NEXT" on the LEFT BUMPER screen.
RIGHT BUMPER
![]() |
By pressing the left and right, up and down and A and B switches, move the right bumper reference line vertically and horizontally or rotate it so that the bumper reference lines overlap or contact the bumper edge line.
Select "NEXT" on the RIGHT BUMPER screen.
VERIFY MODE
![]() |
Check that the bumper reference lines and bumper edge line are nearly overlapping.
Selecting "NEXT" on the VERIFY MODE screen will be completed the camera aiming adjustment.
Finish diagnostic mode.