Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0107    Manifold Absolute Pressure / Barometric Pressure Circuit Low Input

DTC    P0108    Manifold Absolute Pressure / Barometric Pressure Circuit High Input

for Preparation Click here


DESCRIPTION

Refer to DTC P0106 .

DTC No.
DTC Detecting Condition
Trouble Area
P0107
The output voltage from the manifold absolute pressure sensor less than 0.5 V for 0.5 seconds. (1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM
P0108
The output voltage from the manifold absolute pressure sensor more than 4.5 V for 0.5 seconds. (1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM

HINT:
When DTC P0107 or P0108 is detected, check the manifold absolute pressure by selecting Powertrain / Engine and ECT / Data List / Primary / MAP on the Techstream.


Pressure Displayed
Malfunction
Approximately 0 kPa(abs) [0 mmHg(abs)]
  1. Short in PIM circuit to ground
  2. Short in PIM circuit to E2 circuit
  3. Open in VC circuit
130 kPa(abs) [975 mmHg(abs)] or higher
  1. Short in VC circuit to PIM circuit
  2. Open in PIM circuit
  3. Open in E2 circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the manifold absolute pressure. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold absolute pressure sensor and stores a DTC.
Example:
When the sensor output voltage remains less than 0.5 V, or more than 4.5 V for 0.5 seconds, the ECM stored a DTC.

MONITOR STRATEGY


Related DTCs
P0107: Manifold absolute pressure sensor range check (Low voltage)
P0108: Manifold absolute pressure sensor range check (High voltage)
Required Sensor/Components (Main)
Manifold absolute pressure sensor
Required Sensor/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
All of the following conditions are met
-
Time after starter ON to OFF
2 seconds or more
Auxiliary battery voltage
8 V or more
Power switch
On (IG)

TYPICAL MALFUNCTION THRESHOLDS


P0107 
Manifold absolute pressure sensor voltage
Less than 0.5 V

P0108 
Manifold absolute pressure sensor voltage
More than 4.5 V

COMPONENT OPERATING RANGE


Manifold absolute pressure sensor voltage
0.5 to 4.5 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and wait 5 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0107 or P0108.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  13. If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A220563E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (MAP)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAP.

  1. Read the MAP value.

    OK:
    Same value as the actual atmospheric pressure.

HINT:
  1. Standard atmospheric pressure is 101 kPa(abs) [760 mmHg(abs)]. For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).
  2. Also, check "Atmosphere Pressure" in the Data List.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK TERMINAL VOLTAGE (MANIFOLD ABSOLUTE PRESSURE SENSOR)
A209150E11
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-3 (VC) - D3-2 (E2)
    Power switch on (IG)
    4.75 to 5.25 V
    D3-1 (PIM) - D3-2 (E2)
    Power switch on (IG)
    3.0 to 5.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Manifold Absolute Pressure Sensor)

    Result:
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
Go to step 4
A


3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D3-3 (VC) - D28-72 (VCPM)
    Always
    Below 1 Ω
    D3-2 (E2) - D28-71 (EPIM)
    Always
    Below 1 Ω
    D3-1 (PIM) - D28-69 (PIM)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D3-3 (VC) or D28-72 (VCPM) - Body ground
    Always
    10 kΩ or higher
    D3-1 (PIM) or D28-69 (PIM) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (P0107 OR P0108)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Clear the DTC.

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC P0107 or P0108 is output
    B



B
REPLACE ECM (Click here)
A

END