Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0011    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0012    Camshaft Position "A" - Timing Over-Retarded (Bank 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P0010 .

DTC No.
DTC Detection Condition
Trouble Area
P0011
Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM
P0012
Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.
  1. Example:
  2. A DTC is stored when the following conditions "A" and "B" are met:
    1. It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").
    2. After the above condition is met, the camshaft timing oil control valve is forcibly activated for 10 seconds (Condition "B").
  3. The monitor will run if all of the following conditions are met:
  4. DTC P0011 (Advanced Cam Timing) is subject to 1 trip detection logic.
  5. DTC P0012 (Retarded Cam Timing) is subject to 2 trip detection logic.
  6. These DTCs indicate that the VVT controller cannot operate properly due to camshaft timing oil control valve assembly malfunctions or the presence of foreign objects in the camshaft timing oil control valve assembly.

MONITOR STRATEGY


Related DTCs
P0011: Advanced camshaft timing
P0012: Retarded camshaft timing
Required Sensors/Components (Main)
Camshaft timing oil control valve assembly and VVT controller
Required Sensors/Components (Related)
Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
Advanced camshaft timing: Immediately
Retarded camshaft timing: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0010 (Camshaft timing oil control valve assembly bank 1)
P0016 (VVT system bank 1 - misalignment)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
Auxiliary battery voltage
11 V or more
Engine speed
500 to 4000 rpm
Engine coolant temperature
75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS


P0011: Advanced Camshaft Timing 
Both of the following conditions are met
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at advanced valve timing

P0012: Retarded Camshaft Timing 
Both of the following conditions are met
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at retarded valve timing
  1. If the difference between the target and actual camshaft timing is greater than the specified value, the ECM operates the camshaft timing oil control valve assembly for 10 seconds by applying and releasing oil pressure. Then, the ECM monitors the camshaft timing change for 10 seconds.

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A217996E11

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

    HINT:
    1. P0011 is output:
      Clear the DTC not using the Techstream.
    2. P0012 is output:
      Clear the DTC using the Techstream.

  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more [B].
  8. Accelerate the vehicle to 37 mph (60 km/h) or more by depressing the accelerator pedal for 10 seconds or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    If the engine stops, further depress the accelerator pedal to restart the engine.

  9. Idle the engine for 30 seconds or more [D].

    HINT:
    1. P0011 is output:
      With the Park (P) selected.
    2. P0012 is output:
      With the shift lever in D.

  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
  11. Read the pending DTC [E].

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P0011 or P0012.
  14. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  15. Accelerate the vehicle to 37 mph (60 km/h) or more by depressing the accelerator pedal for 10 seconds or more [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  16. Idle the engine for 30 seconds or more [G].
  17. Input the DTC: P0011 or P0012.
  18. Check the DTC judgment result again [H].

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  19. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE

HINT:
  1. DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0011 or P0012 is output
    A
    DTC P0011 or P0012 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).

  1. Check the engine speed while operating the camshaft timing oil control valve assembly using the Techstream.

    Result:

    Techstream Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls

    HINT:
    1. If the result is not acceptable, cool the engine (engine coolant temperature is 50°C (122°F) or less) and perform the Active Test again.
    2. Test not possible with park (P) selected during charge control. Move shift lever to N to perform test.
    3. If the DTCs are stored after the Active Test, clear the DTCs (Click here).



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

    HINT:
    1. P0011 is output:
      Clear the DTC not using the Techstream.
    2. P0012 is output:
      Clear the DTC using the Techstream.

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Driving the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC P0011 or P0012 is output
    B

    HINT:
    DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.



B
Go to step 7
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
  1. Inspect the camshaft timing gear assembly .

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER


    A150883
  1. Remove the oil control valve filter .

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
REPLACE OIL CONTROL VALVE FILTER (Click here)
OK


7.ADJUST VALVE TIMING
A216026E01

HINT:
There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to match-up the alignment marks (Click here).

Text in Illustration 
*1
Top
*2
Alignment Mark
*3
No. 1 Cylinder at TDC Compression

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

    HINT:
    1. P0011 is output:
      Clear the DTC not using the Techstream.
    2. P0012 is output:
      Clear the DTC using the Techstream.

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC P0011 or P0012 is output
    B



B
REPLACE ECM (Click here)
A

END