Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
These DTCs relate to the throttle position sensor.

The throttle position sensor is mounted on the throttle body assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.
The throttle position sensor has 2 sensor circuits, VTA1 and VTA2 each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

A283090E03


DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. ECM
P0121
Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. Throttle position sensor circuit
  3. ECM
P0122
Output voltage of VTA1 0.2 V or less for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. Short in VTA1 circuit
  3. Open in VCTA circuit
  4. ECM
P0123
Output voltage of VTA1 4.535 V or more for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. Open in VTA1 circuit
  3. Open in ETA circuit
  4. Short between VCTA and VTA1 circuits
  5. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. ECM
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. Short in VTA2 circuit
  3. Open in VCTA circuit
  4. ECM
P0223
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. Open in VTA2 circuit
  3. Open in ETA circuit
  4. Short between VCTA and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. Throttle position sensor (built into throttle body assembly)
  3. ECM

MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.
P0120, P0122, P0123, P0220, P0222, P0223 and P2135:
  1. A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.
  2. VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.
  3. VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor circuit, and stores a DTC.
P0121:
  1. This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.
    For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction in the throttle position sensor. The ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0120: Throttle position sensor 1 range check (Chattering)
P0121: Throttle position sensor rationality
P0122: Throttle position sensor 1 range check (Low voltage)
P0123: Throttle position sensor 1 range check (High voltage)
P0220: Throttle position sensor 2 range check (Chattering)
P0222: Throttle position sensor 2 range check (Low voltage)
P0223: Throttle position sensor 2 range check (High voltage)
P2135: Throttle position sensor range check (Correlation)
Required Sensors/Components (Main)
Throttle position sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223
Within 2 seconds: P0121
0.5 seconds: P2135 Case 1
0.4 seconds: P2135 Case 2
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0120, P0122, P0123, P0220, P0222, P0223 and P2135: 
Monitor runs whenever following DTCs are not present
None
Either of the following conditions A or B is met
-
A. Power switch on (IG)
0.012 seconds or more
B. Command to electronic throttle actuator power
ON

P0121: 
Monitor runs whenever following DTCs are not present
None
Both of the following conditions are met
-
Either of the following conditions A or B is met
-
A. Power switch
On (IG)
B. Command to electronic throttle actuator power
ON
Throttle position sensor circuit fail (P0120, P0122, P0123, P0220, P0222, P0223, P2135)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P0120 
VTA1 voltage
0.2 V or less, or 4.535 V or more

P0121 
Either of the following conditions is met
1 or 2
1. Difference of learned throttle position sensor opener position voltage between VTA2 and VTA1
More than 1.6 V
2. Difference of learned throttle position sensor opener position voltage between VTA2 and VTA1
Less than 0.8 V

P0122 
VTA1 voltage
0.2 V or less

P0123 
VTA1 voltage
4.535 V or more

P0220 
Either of the following conditions is met
A or B
A. VTA2 voltage
1.75 V or less
B. Both of the following conditions are met
(a) and (b)
(a) VTA2 voltage
4.8 V or more
(b) VTA1 voltage
0.2 to 2.02 V

P0222 
VTA2 voltage
1.75 V or less

P0223 
VTA2 voltage when VTA1 0.2 to 2.02 V
4.8 V or more

P2135 Case 1 
Difference between VTA1 and VTA2 voltages
0.02 V or less

P2135 Case 2 
Both of the following conditions are met
-
VTA1 voltage
0.2 V or less
VTA2 voltage
1.75 V or less

COMPONENT OPERATING RANGE


All of the following conditions are met
-
VTA1 voltage
Higher than 0.2 V, and less than 4.535 V
VTA2 voltage
Higher than 1.75 V, and less than 4.8 V
Difference between VTA1 and VTA2 voltages
Higher than 0.02 V

CONFIRMATION DRIVING PATTERN


A198824E19

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine.
  8. With the vehicle stationary, fully depress and release the accelerator pedal [B].
  9. Idle the engine for 2 seconds or more [C].
  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  11. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.
  14. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to electronic throttle control system malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM stops the engine and the vehicle can be driven using solely the hybrid system. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

WIRING DIAGRAM


A220105E01


INSPECTION PROCEDURE

HINT:
  1. DTC P0121 is stored when the voltages output from VTA1 and VTA2 are not consistent with the characteristics of the sensors. Therefore, check the Freeze Frame Data when this DTC is output. Use the following formula to confirm relative fluctuations in voltage.

    Characteristic of sensor output:
    VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
    VTA1: Throttle Position No. 1
    VTA2: Throttle Position No. 2

  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
  1. Disconnect the throttle body assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D4-5 (VC) - D28-88 (VCTA)
    Always
    Below 1 Ω
    D4-6 (VTA) - D28-90 (VTA1)
    Always
    Below 1 Ω
    D4-4 (VTA2) - D28-89 (VTA2)
    Always
    Below 1 Ω
    D4-3 (E2) - D28-111 (ETA)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D4-5 (VC) or D28-88 (VCTA) - Body ground
    Always
    10 kΩ or higher
    D4-6 (VTA) or D28-90 (VTA1) - Body ground
    Always
    10 kΩ or higher
    D4-4 (VTA2) or D28-89 (VTA2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT ECM (VC VOLTAGE)


    A194103E34
  1. Disconnect the throttle body assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D4-5 (VC) - D4-3 (E2)
    Power switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Throttle Body Assembly)



NG
REPLACE ECM (Click here)
OK


3.REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the throttle body assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)