Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0128    Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

for Preparation Click here


DESCRIPTION

HINT:
This DTC relates to the water inlet with thermostat sub-assembly.

This DTC is stored when the engine coolant temperature does not reach 75°C (167°F) despite sufficient engine warm-up time having elapsed.

DTC No.
DTC Detection Condition
Trouble Area
P0128
  1. Conditions (a), (b) and (c) are met for 5 seconds (2 trip detection logic):
  2. (a) Cold start
  3. (b) Engine warmed up
  4. (c) Engine coolant temperature less than 75°C (167°F)
  1. Water inlet with thermostat sub-assembly
  2. Cooling system
  3. Engine coolant temperature sensor
  4. Front exhaust pipe assembly
  5. ECM

MONITOR DESCRIPTION


A121605E23

The ECM estimates the engine coolant temperature based on the starting temperature, engine loads, and engine speeds. The ECM then compares the estimated temperature with the actual engine coolant temperature. When the estimated engine coolant temperature reaches 75°C (167°F), the ECM checks the actual engine coolant temperature. If the actual engine coolant temperature is less than 75°C (167°F), the ECM interprets this as a malfunction in the water inlet with thermostat sub-assembly or the engine cooling system and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0128: Coolant Thermostat
Required Sensors/Components (Main)
Water inlet with thermostat sub-assembly
Required Sensors/Components (Related)
Engine coolant temperature sensor
Intake air temperature sensor
Frequency of Operation
Once per driving cycle
Duration
600 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010 (Camshaft timing oil control valve assembly bank 1)
P0011 (VVT system bank 1 - advance)
P0012 (VVT system bank 1 - retard)
P0016 (VVT system bank 1 - misalignment)
P0031, P0032, P101D (Air fuel ratio sensor heater - sensor 1)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P014C, P014D (Air fuel ratio sensor - slow response)
P015A, P015B (Air fuel ratio sensor - delayed response)
P0171, P0172 (Fuel system)
P0301, P0302, P0303, P0304 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0351, P0352, P0353, P0354 (Igniter)
P0401 (EGR system (closed))
P2195, P2196 (Air fuel ratio sensor - rationality)
P219A, P219C, P219D, P219E, P219F (Air fuel ratio sensor - imbalance)
P2237 (Air fuel ratio sensor - open)
P2238, P2252 (Air fuel ratio sensor - low impedance)
P2239, P2253 (Air fuel ratio sensor - high impedance)
Auxiliary battery voltage
11 V or more
Either of the following conditions 1 or 2 is met:
-
1. All of following conditions are met:
(a), (b) and (c)
(a) Engine coolant temperature at engine start - Intake air temperature at engine start
-15 to 7°C (-27 to 12.6°F)
(b) Engine coolant temperature at engine start
-10 to 56°C (14 to 133°F)
(c) Intake air temperature at engine start
-10 to 56°C (14 to 133°F)
2. All of the following conditions are met:
(a), (b) and (c)
(a) Engine coolant temperature at engine start - Intake air temperature at engine start
More than 7°C (12.6°F)
(b) Engine coolant temperature at engine start
56°C (133°F) or less
(c) Intake air temperature at engine start
-10°C (14°F) or more
Accumulated time at 80 mph (128 km/h) or more
Less than 20 seconds

TYPICAL MALFUNCTION THRESHOLDS


Duration that both of the following conditions (a) and (b) are met
5 seconds or more
(a) Estimated engine coolant temperature
75°C (167°F) or more
(b) Engine coolant temperature sensor output
Less than 75°C (167°F)

CONFIRMATION DRIVING PATTERN


A255184E02

  1. Stop the engine and allow it to soak.
  2. Connect the Techstream to the DLC3.
  3. Turn the power switch on (IG) and turn the Techstream on [A].
  4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp and Intake Air.
  5. Check that "Coolant Temp" is 56°C (133°F) or less, and "Intake Air" is between 0 and 35°C (32 and 95°F).
  6. Set the heater to MAX HOT with fresh air mode selected and turn the A/C off.
  7. Start the engine and drive the vehicle at 80 km/h (50 mph) for 15 minutes [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. After "Coolant Temp" stabilizes, check that "Coolant Temp" is 75°C (167°F) or higher [C].

    HINT:
    If "Coolant Temp" is less than 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and thermostat.


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. When the DTC is output, check the engine coolant temperature using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0128)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0128 is output
    A
    DTC P0128 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0128 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.

    Result 
    Result
    Proceed to
    OK (w/ exhaust heat recirculation system)
    A
    NG
    B
    OK (w/o exhaust heat recirculation system)
    C



B
REPAIR OR REPLACE COOLING SYSTEM

C
Go to step 4
A


3.INSPECT FRONT EXHAUST PIPE ASSEMBLY
  1. Inspect the front exhaust pipe assembly (exhaust flow control valve operation) .



NG
REPLACE FRONT EXHAUST PIPE ASSEMBLY (Click here)
OK


4.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
  1. Inspect the water inlet with thermostat sub-assembly opening temperature (Click here).



NG
REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)