Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and a pickup coil.
The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The No. 1 crankshaft position sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
When either of following conditions are met:
(1 trip detection logic)
  1. Missing crankshaft position sensor signal despite camshaft position sensor signal inputs normal after engine cranked
  1. No crankshaft position sensor signal to ECM while engine running
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 1 crankshaft position sensor plate
  4. ECM

  1. A254145E02
    Reference: Inspection using an oscilloscope.

    HINT:
    1. The correct waveform is as shown.
    2. A failure of the ground for the shielding of the wiring may result in noisy waveforms.

    ECM Terminal Name
    Between NE+ and NE-
    Tester Range
    5 V/DIV., 20 ms./DIV.
    Condition
    Idling with warm engine

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor verify pulse input
P0335: Crankshaft position sensor range check/rationality
Required Sensors/Components (Main)
Crankshaft position sensor
Required Sensors/Components (Related)
Camshaft position sensor
Frequency of Operation
Continuous
Duration
1.85 seconds: Verify pulses input (case 1)
15 seconds: Verify pulses input (case 2)
0.016 seconds: Range check/rationality
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs are not present
None

P0335: Crankshaft Position Sensor Verify Pulse Input (Case 1) 
All of the following conditions are met
-
Power switch
On (IG)
Time after power switch off to on (IG)
0.5 seconds or more
Lost communication with power management control ECU (U0293)
Not detected

P0335: Crankshaft Position Sensor Verify Pulse Input (Case 2) 
All of the following conditions are met
-
Time after power switch off to on (IG)
0.5 seconds or more
Engine speed (Top dead center)
600 rpm or more
Engine speed (30°CA)
600 rpm or more
Starter
OFF
Time after starter ON to OFF
3 seconds or more
Lost communication with power management control ECU (U0293)
Not detected

P0335: Crankshaft Position Sensor Range Check/Rationality 
All of the following conditions are met
-
Engine speed signal
Signal input
Power switch
On (IG)
Time after starter OFF to ON
2.5 seconds or more
Camshaft position sensor circuit fail
Not detected
Number of camshaft position sensor signal pulse
6 times
Auxiliary Battery voltage
7 V or higher
Lost communication with power management control ECU (U0293)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P0335: Crankshaft Position Sensor Verify Pulse Input (Case 1) 
Crankshaft position sensor signal
No signal

P0335: Crankshaft Position Sensor Verify Pulse Input (Case 2) 
Crankshaft position sensor signal
No signal

P0335: Crankshaft Position Sensor Range Check/Rationality 
Number of crankshaft position sensor signal pulse
87 times or less, or 219 times or more

COMPONENT OPERATING RANGE


Crankshaft position sensor
  1. Crankshaft position sensor output voltage fluctuates while crankshaft revolving
  2. 34 crankshaft position sensor signals per crankshaft revolution

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine.
  8. Idle the engine for 20 seconds or more [A].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0335.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A216523E09


INSPECTION PROCEDURE

HINT:
  1. After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.
    1. Installation condition of the camshaft position sensor
    2. Installation condition of the camshaft
    3. Connection of the camshaft position sensor connector
  2. If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  3. Check the engine speed. The engine speed can be checked using the Techstream. To check, follow the operation below:
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG) and turn the Techstream on.
    3. Put the engine in inspection mode (maintenance mode) (Click here).
    4. Start the engine.
    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine rotating normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the Techstream while the engine is running.

    OK:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the Techstream.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the Techstream remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D27-1 (NE) - D28-74 (NE+)
    Always
    Below 1 Ω
    D27-2 (NE-) - D28-120 (NE-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D27-1 (NE) or D28-74 (NE+) - Body ground
    Always
    10 kΩ or higher
    D27-2 (NE-) or D28-120 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E25
  1. Check the crankshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Check the teeth of the No. 1 crankshaft position sensor plate (Click here).

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE (Click here)
OK


6.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC P0335 is output
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END