Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM

DYNAMIC RADAR CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

The cruise control main switch operates 8 functions: SET, -(COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, CANCEL, and MODE. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while it is being operated it in the direction of each arrow and turns off after being released. The internal contact points of the cruise control main switch are turned on with the switch operation. The driving support ECU then reads the voltage value that has been changed by the switch operation to control MODE, SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL. The dynamic radar cruise control system has two cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode.
  1. Vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.
  2. The operation of constant speed control mode is the same as that for a conventional cruise control system.

WIRING DIAGRAM


E184028E03


INSPECTION PROCEDURE

1.INSPECT CRUISE CONTROL MAIN SWITCH


  1. Remove the cruise control main switch (Click here).


    E107856E21


    Text in Illustration 
    *1
    Component without harness connected
    (Cruise Control Main Switch)
    *2
    ON-OFF
    *3
    CANCEL
    *4
    -SET
    *5
    +RES
    *6
    MODE

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Switch Condition
Specified Condition
1 - 2
1 - 3
Main switch off
1 MΩ or higher
1 - 3
Main switch on
Below 2.5 Ω
1 - 2
MODE
Below 2.5 Ω
1 - 3
+ RES
235 to 245 Ω
1 - 3
- SET
617 to 643 Ω
1 - 3
CANCEL
1509 to 1571 Ω

  1. Reinstall the cruise control main switch (Click here).



NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - CRUISE CONTROL MAIN SWITCH)


    E103330E69
  1. Disconnect the connector from the spiral with sensor cable sub-assembly.

  1. Disconnect the connector from the cruise control main switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Cruise control main switch side connector terminal 1 - z10-4
    Always
    Below 1 Ω
    Cruise control main switch side connector terminal 2 - z10-1
    Always
    Below 1 Ω
    Cruise control main switch side connector terminal 3 - z10-3
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)
    *2
    Front view of wire harness connector
    (to Cruise Control Main Switch)

  1. Reconnect the connector to the spiral with sensor cable sub-assembly.

  1. Reconnect the connector to the cruise control main switch.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL MAIN SWITCH)
OK


3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NOTICE:
The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may cause airbag deployment. Be sure to read the page shown in the brackets.



    E144333E60
  1. Remove the spiral with sensor cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    z10-1 - L52-7 (R/N)
    The spiral with sensor cable sub-assembly is centered
    Below 1 Ω
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the left
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the right
    z10-3 - L52-1 (CCS)
    The spiral with sensor cable sub-assembly is centered
    Below 1 Ω
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the left
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the right
    z10-4 - L52-2 (ECC)
    The spiral with sensor cable sub-assembly is centered
    Below 1 Ω
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the left
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the right

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral with Sensor Cable Sub-assembly)

    HINT:
    The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.

  1. Install the spiral with sensor cable sub-assembly (Click here).



NG
REPLACE SPIRAL WITH CABLE SUB-ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)
  1. Disconnect the driving support ECU connector.

  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    L60-23 (CCS) - L52-1 (CCS)
    Always
    Below 1 Ω
    L60-10 (CCHG) - L52-7 (R/N)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    L60-23 (CCS) or L52-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    L60-10 (CCHG) or L52-7 (R/N) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the driving support driving support ECU connector.

  1. Reconnect the spiral with sensor cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)


    E171248E09
  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    L52-2 (ECC) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)

  1. Reconnect the spiral with sensor cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)