Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM

DYNAMIC RADAR CRUISE CONTROL SYSTEM > Distance Control Switch Circuit

for Preparation Click here


DESCRIPTION

The distance control switch sets vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch RH. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch RH (distance control switch) while the dynamic radar cruise control system is operating.

WIRING DIAGRAM


E169168E22


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (DISTANCE CONTROL SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Radar Cruise / Data List / Distance Control Switch.

  1. Check the Data List proper functioning of the distance control switch.

    Radar Cruise 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Distance Control Switch
    Distance control switch signal / ON or OFF
    ON: Distance control switch on
    OFF: Distance control switch off
    -

    OK:
    When the distance control switch is operated, the display changes in accordance with switch operation.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH RH


  1. Remove the steering pad switch RH (Click here).


    E254400E01


    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch RH)
    *2
    Distance Control Switch

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z9-4 - z9-6
    Distance control switch ON
    Below 2.5 Ω
    z9-4 - z9-6
    Distance control switch OFF
    10 kΩ or higher

  1. Install the steering pad switch RH (Click here).



NG
REPLACE STEERING PAD SWITCH RH (Click here)
OK


3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NOTICE:
The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may cause airbag deployment. Be sure to read the page shown in the brackets.



    E144333E61
  1. Remove the spiral with sensor cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    z9-4 - L52-11 (DIST)
    The spiral with sensor cable sub-assembly is centered
    Below 1 Ω
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the left
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the right
    z9-6 - L52-2 (ECC)
    The spiral with sensor cable sub-assembly is centered
    Below 1 Ω
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the left
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the right

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral with Sensor Cable Sub-assembly)

HINT:
The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.

  1. Install the spiral with sensor cable sub-assembly (Click here).



NG
REPLACE SPIRAL WITH CABLE SUB-ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)
  1. Disconnect the driving support ECU connector.

  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    L60-6 (SPSW) - L52-11 (DIST)
    Always
    Below 1 Ω
    L60-6 (SPSW) or L52-11 (DIST) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the driving support ECU connector.

  1. Reconnect the spiral with sensor cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)


    E171248E10
  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    L52-2 (ECC) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)

  1. Reconnect the spiral with sensor cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)
OK

REPLACE DRIVING SUPPORT ECU (Click here)