Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1497/97    BUS IC Communication Malfunction

for Preparation Click here


DESCRIPTION

The air conditioning harness connects the A/C amplifier and each servo. The A/C amplifier supplies power and sends operation instructions to each servo through the air conditioning harness. Each servo sends the damper position information to the A/C amplifier.

DTC No.
DTC Detection Condition
Trouble Area
B1497/97
Communication line error or open
  1. Air conditioning harness
  2. Air mix control servo motor
  3. Air outlet control servo motor
  4. Air inlet control servo motor
  5. A/C amplifier

WIRING DIAGRAM


E232077E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING A/C AMPLIFIER
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Air mix control servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Outlet Servo Pulse (D)
    Air outlet outlet servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Inlet Damper Targ Pulse
    Air inlet outlet damper target pulse
    Min.: 0, Max.: 255
    -

    OK:
    Arm of the servo motor selected in the Active Test moves smoothly

  1. According to the test, proceed to the next step.

    Result:
    Result
    Proceed to
    One of the servo motors is malfunctioning
    A
    All of the servo motors are malfunctioning
    B



B
REPLACE AIR CONDITIONING HARNESS ASSEMBLY
A


2.SYSTEM CHECK
  1. According to the test, proceed to the next step.

    Result:
    Result
    Proceed to
    Only the air mix control servo motor is malfunctioning
    A
    Only the air outlet control servo motor is malfunctioning
    B
    Only the air inlet control servo motor is malfunctioning
    C



B
Go to step 4

C
Go to step 5
A


3.REPLACE AIR MIX CONTROL SERVO MOTOR
  1. Replace the air mix control servo motor (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 6
A

END 

4.REPLACE AIR INLET CONTROL SERVO MOTOR
  1. Replace the air outlet control servo motor (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 6
A

END 

5.REPLACE AIR OUTLET CONTROL SERVO MOTOR
  1. Replace the air inlet control servo motor (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 6
A

END 

6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness (Click here).

    HINT:
    Since the air conditioning harness cannot be inspected while it is removed from the vehicle, replace the air conditioning harness with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
E232078E01
  1. Disconnect the A/C amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    L17-21 (B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to A/C Amplifier)



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)