Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > MIL Circuit

for Preparation Click here


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detected by the ECM. When the power switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually: When the power switch is turned on (IG), the MIL should illuminate and should then turn off after turn the power switch on (READY). If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the Techstream.

WIRING DIAGRAM


A217388E10


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK THAT MIL IS ILLUMINATED
  1. Check the illumination of the MIL.

    Result:

    Condition
    Proceed to
    MIL remains on
    A
    MIL remains off (Does not illuminate at all)
    B
    MIL illuminates and should turn off after power switch on (READY)
    C



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK WHETHER MIL TURNS OFF
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check if any DTCs have been stored. Note down the DTCs.

  1. Clear the DTCs (Click here).

  1. Check if the MIL goes off.

    OK:
    MIL goes off.



NG
Go to step 3
OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)  

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)


    A194151E82
  1. Disconnect the A57 ECM connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

  1. Turn the power switch on (IG).

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.



NG
Go to step 4
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - ECM)
  1. Disconnect the No. 3 meter circuit plate connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    L27-25 (EFI) or A57-36 (W) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 3 METER CIRCUIT PLATE (Click here)  

5.CHECK THAT ENGINE STARTS
  1. Turn the power switch on (IG).

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

    Result:

    Result
    Proceed to
    Engine starts
    A
    Engine cannot be put in inspection mode*
    (Engine cannot start)
    B

    HINT:
    *: The Techstream cannot communicate with the ECM.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


6.CHECK HARNESS AND CONNECTOR (ECM TERMINAL VOLTAGE)


    A194151E66
  1. Disconnect the ECM connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A57-36 (W) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 7
OK

REPLACE ECM (Click here)  

7.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - ECM)
  1. Disconnect the No. 3 meter circuit plate connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    L27-25 (EFI) - A57-36 (W)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 3 METER CIRCUIT PLATE (Click here)