Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is output, check the No. 1 ignition coil assembly circuit.
  3. If DTC P0352 is output, check the No. 2 ignition coil assembly circuit.
  4. If DTC P0353 is output, check the No. 3 ignition coil assembly circuit.
  5. If DTC P0354 is output, check the No. 4 ignition coil assembly circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is an ignition system in which each cylinder is ignited by it's own ignition coil assembly and spark plug. The secondary wiring of each ignition coil generates a powerful voltage which is applied directly to each spark plug. The spark passes from the center electrode of the spark plug to the ground electrode.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A255924E05


DTC No.
DTC Detection Conditions
Trouble Areas
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF or IGT circuit (1 to 4) between ignition coil assembly and ECM
  3. No. 1 to No. 4 ignition coil assemblies
  4. ECM
Reference: Inspection using an oscilloscope.
A289263E04

HINT:
While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF and E1 of the ECM connector.

ECM Terminal Name
CH1: Between IGT (1 to 4) and E1
CH2: Between IGF and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling

MONITOR DESCRIPTION


A212405E21

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (cylinder 1) range check/functional check
P0352: Igniter (cylinder 2) range check/functional check
P0353: Igniter (cylinder 3) range check/functional check
P0354: Igniter (cylinder 4) range check/functional check
Required Sensors/Components (Main)
Igniter
Required Sensors/Components (Related)
ECM
Frequency of Operation
Continuous
Duration
-
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
All of the following conditions are met
-
Either of the following conditions A or B is met
-
A. Engine speed
1500 rpm or less
B. Starter
OFF
Either of the following conditions C or D met
-
C. Both of the following conditions (a) and (b) are met
-
(a) Engine speed
500 rpm or less
(b) Auxiliary battery voltage
6 V or more
D. All of the following conditions (a), (b) and (c) are met
-
(a) Engine speed
More than 500 rpm
(b) Auxiliary battery voltage
10 V or more
(c) Number of sparks after CPU reset
5 sparks or more
Lost communication with power management control ECU (U0293)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


All of the following conditions are met
Conditions A, B, C and D
A. Ignition signal fail counter
More than 2 times
B. Time after condition A is met
0.256 seconds or more
C. Ignition signal fail count after condition B is met
More than 2 times
D. Power switch
On (IG)

COMPONENT OPERATING RANGE


Confirmed ignition signal input when ignition signal is ON to OFF
2 times

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine.
  8. Idle the engine for 10 seconds or more [A].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0351, P0352, P0353 or P0354.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A220106E01


A216529E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
  1. Disconnect the ignition coil assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D23-4 (GND) - Body ground
    Always
    Below 1 Ω
    D22-4 (GND) - Body ground
    Always
    Below 1 Ω
    D21-4 (GND) - Body ground
    Always
    Below 1 Ω
    D20-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)


    A194110E60
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D23-1 (+B) - D23-4 (GND)
    Power switch on (IG)
    11 to 14 V
    D22-1 (+B) - D22-4 (GND)
    Power switch on (IG)
    11 to 14 V
    D21-1 (+B) - D21-4 (GND)
    Power switch on (IG)
    11 to 14 V
    D20-1 (+B) - D20-4 (GND)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - IG2 RELAY)
OK


3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D23-2 (IGF) - D28-23 (IGF)
    Always
    Below 1 Ω
    D22-2 (IGF) - D28-23 (IGF)
    Always
    Below 1 Ω
    D21-2 (IGF) - D28-23 (IGF)
    Always
    Below 1 Ω
    D20-2 (IGF) - D28-23 (IGF)
    Always
    Below 1 Ω


    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D23-3 (IGT1) - D28-108 (IGT1)
    Always
    Below 1 Ω
    D22-3 (IGT2) - D28-107 (IGT2)
    Always
    Below 1 Ω
    D21-3 (IGT3) - D28-106 (IGT3)
    Always
    Below 1 Ω
    D20-3 (IGT4) - D28-105 (IGT4)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D23-2 (IGF), D22-2 (IGF), D21-2 (IGF), D20-2 (IGF) or D28-23 (IGF) - Body ground
    Always
    10 kΩ or higher


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D23-3 (IGT1) or D28-108 (IGT1) - Body ground
    Always
    10 kΩ or higher
    D22-3 (IGT2) or D28-107 (IGT2) - Body ground
    Always
    10 kΩ or higher
    D21-3 (IGT3) or D28-106 (IGT3) - Body ground
    Always
    10 kΩ or higher
    D20-3 (IGT4) or D28-105 (IGT4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Shuffle arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B

    HINT:
    Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)