Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > INITIALIZATION

for Preparation Click here



DESCRIPTION OF INITIALIZATION
  1. Perform initialization in the following cases:

    1. Before delivery of a new vehicle.
    2. After replacement of the tire pressure warning ECU*.
    3. After replacement of any of the tire pressure warning valve and transmitters*.
    *: Perform initialization after the transmitter ID registration is completed (Click here).

  2. Before initialization

    1. Set the all tire pressure to the specified value (Click here).

      NOTICE:
      Make sure the tires are cooled down.


INITIALIZATION PROCEDURE
  1. Adjust all tire (except spare tire) to the standard tire inflation pressure, as indicated on the tire and loading information label on the vehicle.

  2. Turn the power switch on (IG).



  3. Push and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.


    C210230E01

  4. Turn the power switch off.

  5. Connect the Techstream to the DLC3.

  6. Turn the power switch on (IG).

  7. Turn the Techstream on.

  8. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  9. Check that the initialization has been completed.



  10. H102676E01
  11. Confirm that the tire pressure data of all wheels are displayed on the Techstream.

    NOTICE:
    1. The initialization is normally completed within 2 or 3 minutes.
    2. If the initialization has not been completed successfully, DTC C2177/77 is set after a vehicle speed 8 km/h (5 mph) or more continues for 20 minutes or more.
    3. The initialization can be terminated by connecting terminals TC and CG of the DLC3.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    1. The initialization is completed when the "ID Tire Information Pressure" display shows the correct pressures.
    2. *: It may take about 2 or 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (Click here).