DTC C2121/21 No Signal from Transmitter ID1 |
DTC C2122/22 No Signal from Transmitter ID2 |
DTC C2123/23 No Signal from Transmitter ID3 |
DTC C2124/24 No Signal from Transmitter ID4 |
DTC C2181/81 Transmitter ID1 not Received (Test Mode DTC) |
DTC C2182/82 Transmitter ID2 not Received (Test Mode DTC) |
DTC C2183/83 Transmitter ID3 not Received (Test Mode DTC) |
DTC C2184/84 Transmitter ID4 not Received (Test Mode DTC) |
| DTC No. | DTC Detection Condition | Trouble Area |
| C2121/21 C2122/22 C2123/23 C2124/24 | Following condition (a) or (b) is met: (a) When all conditions below are met:
|
|
| C2181/81 C2182/82 C2183/83 C2184/84 | Test mode procedure is performed. |
|

| 1.CHECK FREQUENCY RECEIVING CONDITION |
Check that the vehicle is not located in an area such as described below:
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
Devices using similar radio frequencies are used in the vehicle.
|
| ||||
| OK | |
| 2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC |
Set the tire pressure to the specified values (Click here).
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID1 Tire Inflation Pressure | ID1 tire inflation pressure/ min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds.
Check the Data List.
After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID4) has changed, repeat this procedure one by one. Identify the transmitter that corresponds to the DTC.
| Result | Proceed to |
| One or more of transmitters abnormal | A |
| All normal | B |
| All abnormal | C |
|
| ||||
|
| ||||
| C | |
| 3.CHECK HARNESS AND CONNECTOR (ECU - RECEIVER) |
Disconnect the L4 ECU connector.
Disconnect the R2 receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L4-12 (RDA) - R2-1 (RDA) | Always | Below 1 Ω |
| L4-11 (GND2) - R2-4 (GND) | ||
| L4-6 (RF5V) - R2-5 (+5V) | ||
| L4-12 (RDA) - Body ground | 10 kΩ or higher | |
| L4-11 (GND2) - Body ground | ||
| L4-6 (RF5V) - Body ground |
|
| ||||
| OK | |
| 4.CHECK TRANSMITTER ID |
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID1 Tire Inflation Pressure | ID1 tire inflation pressure/ min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
Check the ID number on the identified transmitter by removing it from the tire and wheel.

Confirm that the ID number on the transmitter and recorded transmitter ID match.
| Result | Proceed to |
| Match | A |
| Do not match | B |
|
| ||||
| A | |
| 5.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER |
Replace the tire pressure warning valve and transmitter (Click here).
| NEXT | |
| 6.REGISTRATION OF TRANSMITTER ID |
Perform registration (Click here).
| NEXT | |
| 7.PERFORM INITIALIZATION |
Perform initialization (Click here).
| NEXT | |
| 8.READ VALUE USING TECHSTREAM (DATA LIST) |
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID1 Tire Inflation Pressure | ID1 tire inflation pressure/ min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| Result | Proceed to |
| All tire pressure readings are equal to specified values. | A |
| Tire pressure values are not displayed. | B |
|
| ||||
| B | |
| 9.REPLACE TIRE PRESSURE WARNING ANTENNA AND RECEIVER |
Replace the tire pressure warning antenna and receiver (Click here).
| NEXT | |
| 10.READ VALUE USING TECHSTREAM (DATA LIST) |
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID1 Tire Inflation Pressure | ID1 tire inflation pressure/ min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| ID4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2, -14 psi) max.: Absolute pressure / 638 kPa (6.4 kgf/cm2, 93 psi), Relative pressure / 538 kPa (5.4 kgf/cm2, 78 psi) | Actual tire inflation pressure | If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.* |
| Result | Proceed to |
| All tire pressure readings are equal to specified values. | A |
| Tire pressure values are not displayed. | B |
|
| ||||
| A | ||
| ||