DTC P0A93-346 Inverter Cooling System Performance |

| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0A93 | 346 | Inverter cooling system malfunction Inverter coolant temperature increases as well as the temperature of any inverter with converter assembly related parts increases. (1 trip detection logic) |
|
| DTC No. | Data List |
| P0A93-346 |
|
| Related DTCs | P0A93 (INF 346): HV cooling system malfunction |
| Required sensors / components | Water pump, radiator fan, inverter, boost converter |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | 1 driving cycle |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
| TMC's intellectual property | - |
| Inverter cooling system | DTC P0A93 (INF 346) is not detected |

| 1.CHECK VEHICLE CONDITION |
Make sure that the front side of the radiator grille is not blocked with anything.
Ask the customer if the front side of the radiator grille was blocked with anything.
| Result | Proceed to |
| Not blocked. | A |
| Is/was blocked. | B |
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (HV) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| P0A93-346 only is output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
| P0A02-719 | Motor Electronics Coolant Temperature Sensor Circuit Low |
| P0A03-720 | Motor Electronics Coolant Temperature Sensor Circuit High |
| P0C73-776 | Motor Electronics Coolant Pump "A" Control Performance |
| P314A-828 | Inverter Coolant Pump Speed Signal |
Turn the power switch off.
|
| ||||
| A | |
| 3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR) |
![]() |
Check that the service plug grip is not installed.
Check the connection of the low voltage connector of the inverter with converter assembly.
|
| ||||
| OK | |
| 4.CHECK QUANTITY OF HV COOLANT |
Check the coolant level in the inverter reserve tank.
Check for coolant leaks.
| Result | Proceed to |
| No leaks are found and coolant level in the inverter reserve tank assembly is above the low line. | A |
| No leaks are found and coolant level in the inverter reserve tank assembly is below the low line. | B |
| HV coolant leaks are evident. | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK COOLANT HOSE |
Check if the hoses of the cooling system are kinked or clogged.
|
| ||||
| OK | |
| 6.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE ELECTRIC COOLING FAN) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear DTCs and freeze frame data.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.
Perform the "Control the Electric Cooling Fan" Active Test.
Turn the power switch off.
|
| ||||
| OK | |
| 7.READ VALUE USING TECHSTREAM |
Turn the power switch off and leave the vehicle for at least 1 hour.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Coolant Water Temperature, Inverter Temp (MG2), Cnv Tmp (Upper), Cnv Temp (Lower), Inverter Temp (MG1).
Read the Data List.
| Result | Proceed to |
| Other than below. | A |
| "Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 36°F (20°C) or more. | B |
Turn the power switch off.
|
| ||||
| A | |
| 8.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Read the freeze frame data Ambient Temperature using the Techstream.
Check if the freeze frame data Ambient Temperature is below freezing.
| Result | Proceed to |
| Ambient Temperature value is below freezing temperature of the HV coolant | A |
| Ambient Temperature value is above freezing temperature of the HV coolant | B |
Turn the power switch off.
|
| ||||
| A | |
| 9.REPLACE HV COOLANT |
Replace the HV coolant with coolant having an appropriate concentration (appropriate freeze point) for the vehicle usage conditions (Click here).
| NEXT | ||
| ||