Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The center airbag sensor assembly communication circuit consists of the occupant classification ECU and center airbag sensor assembly.
DTC B1790 is stored when a malfunction is detected in the center airbag sensor assembly communication circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1790
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the center airbag sensor assembly communication circuit.
  2. Occupant classification ECU malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat wire RH
  3. Occupant classification ECU
  4. Center airbag sensor assembly

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant classification ECU. When DTC B1790 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C167958E13


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and occupant classification ECU. Also check that the connectors that link the front seat wire RH and No. 2 floor wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and occupant classification ECU. Also disconnect the connectors that link the front seat wire RH and No. 2 floor wire.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)


    C169178E08
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (FSR+) - Body ground
    Power switch on (IG)
    Below 1 V
    W3-4 (FSR-) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *4
    Connector E



NG
Go to step 11
OK


3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)


  1. Turn the power switch off.


    C210652E01

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Using SST, connect terminals 12 (FSR+) and 13 (FSR-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (FSR+) - W3-4 (FSR-)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *4
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *5
    Connector B
    *6
    Connector E



NG
Go to step 12
OK


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)


    C169178E08
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (FSR+) - W3-4 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *4
    Connector E



NG
Go to step 13
OK


5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)


    C169178E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    W3-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *4
    Connector E



NG
Go to step 14
OK


6.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and center airbag sensor assembly.

  1. Connect the Techstream to the DLC3.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminals.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


8.RECHECK DTC
  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using the Techstream, perform Zero Point Calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform Sensitivity Check (Click here).

    Standard:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END 

11.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C210653E01
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    SW1-1 (FSR+) - Body ground
    Power switch on (IG)
    Below 1 V
    SW1-4 (FSR-) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *6
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

12.CHECK NO. 2 FLOOR WIRE (OPEN)


  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.


    C210654E01

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SW1-1 (FSR+) - SW1-4 (FSR-)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *6
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *7
    Connector B
    *8
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

13.CHECK NO. 2 FLOOR WIRE (SHORT)


    C210653E01
  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SW1-1 (FSR+) - SW1-4 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *6
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

14.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C210653E01
  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SW1-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    SW1-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *6
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH