POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH |

| 1.READ VALUE USING TECHSTREAM (Main Body) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Communication RL-Door Motor | Connection status between power window regulator motor (for rear LH) and main body ECU (multiplex network body ECU) / OK or STOP | OK: Normal communication STOP: Communication stopped | - |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (RL-Door Motor) |
Enter the following menus: Body Electrical / RL-Door Motor / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RL Door P/W Up SW | Rear LH side power window manual up switch signal / ON or OFF | ON: Rear LH door power window manual up switch operated OFF: Rear LH door power window manual up switch not operated | - |
| RL Door P/W Down SW | Rear LH side power window manual down switch signal / ON or OFF | ON: Rear LH door power window manual down switch operated OFF: Rear LH door power window manual down switch not operated | - |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (RL-Door Motor) |
Enter the following menus: Body Electrical / RL-Door Motor / Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Power window | OFF / UP / DOWN | - |
|
| ||||
| OK | ||
| ||
| 4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Side) |
![]() |
Remove the power window regulator switch assembly (for rear LH side) (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 6 (UP) - 1 (GND) | Auto up or up position | Below 1 Ω |
| 7 (DOWN) - 1 (GND) | Auto down or down position | Below 1 Ω |
| *1 | Component without harness connected (Power Window Regulator Switch Assembly (for Rear LH Side)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR LH SIDE SWITCH - REAR LH SIDE MOTOR AND BODY GROUND) |
![]() |
Disconnect the power window regulator motor assembly (for rear LH side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q2-1 (GND) - Body ground | Always | Below 1 Ω |
| Q2-6 (UP) - Q4-10 (UP) | Always | Below 1 Ω |
| Q2-7 (DOWN) - Q4-7 (DOWN) | Always | Below 1 Ω |
| Q2-6 (UP) - Body ground | Always | 10 kΩ or higher |
| Q2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Q4-10 (UP) - Body ground | Always | 10 kΩ or higher |
| Q4-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Power Window Regulator Switch Assembly (for Rear LH Side)) |
| *2 | Front view of wire harness connector (to Power Window Regulator Motor Assembly (for Rear LH Side)) |
|
| ||||
| OK | ||
| ||