Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM

VEHICLE PROXIMITY NOTIFICATION SYSTEM > There is No Sound Made

for Preparation Click here


DESCRIPTION

The vehicle approaching speaker controller receives stop light switch signals from the stop light control relay, vehicle speed signals from the combination meter assembly, engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the transmission control ECU assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM


E289169E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Using the Techstream, enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    DTC B1350 is not output
    A
    DTC B1350 is output
    B
    Communication with the Techstream is not possible
    C



B
GO TO DTC CHART B1350 (Click here)

C
GO TO DIAGNOSTIC PROCEDURE (The diagnostic tool cannot communicate with the vehicle approaching warning system) (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.

  1. Check the operation by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Proximity Sound (Vehicle Stationary)
    Proximity sound (Vehicle stationary)
    OFF or ON
    Produces warning sound when vehicle is stopped

Result:
Result
Proceed to
The warning sound is produced
A
The warning sound is not produced
B



B
Go to step 10
A


3.READ VALUE USING TECHSTREAM (Stop Light SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Check the value(s) by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    -

    Result:
    Result
    Proceed to
    The Techstream display changes according to brake pedal operation
    A
    The Techstream display does not change according to brake pedal operation
    B



B
Go to step 13
A


4.READ VALUE USING TECHSTREAM (Vehicle Speed)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Check the value(s) by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost the same as actual vehicle speed
    -

    Result:
    Result
    Proceed to
    The Techstream display changes according to the vehicle speed
    A
    The Techstream display does not change according to the vehicle speed
    B



B
Go to step 15
A


5.READ VALUE USING TECHSTREAM (Oil Pressure SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Check the value(s) by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Oil Pressure SW
    Oil pressure switch / OFF or ON
    OFF: Engine started
    ON: Engine not started
    -

    Result:
    Result
    Proceed to
    The Techstream display changes according to engine operation
    A
    The Techstream display does not change according to engine operation
    B



B
Go to step 17
A


6.READ VALUE USING TECHSTREAM (Shift Position)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Check the value(s) by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift Position
    P position switch / Not Parking or Parking
    Not Parking or Parking
    -

    Result:
    Result
    Proceed to
    The Techstream display changes according to the selected shift state
    A
    The Techstream display does not change according to the selected shift state
    B



B
Go to step 7
A

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

7.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER
  1. Disconnect the A23 transmission control ECU assembly connector.



    E285951E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-20 (IND) - Body ground
    Power switch on (IG)
    8 V or higher
    Power switch off
    Below 2.5 V

Text in Illustration 
*a
Front view of wire harness connector
(to Transmission Control ECU Assembly)


NG
Go to step 9
OK


8.CHECK TRANSMISSION CONTROL ECU ASSEMBLY
  1. Reconnect the A23 transmission control ECU assembly connector.



    E285952E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-20 (IND) - Body ground
    Power switch on (IG), park (P) selected
    Below 2.5 V
    Power switch on (IG), park (P) not selected
    8 V or higher

Text in Illustration 
*a
Component with harness connected
(Transmission Control ECU Assembly)


NG
REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

9.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - TRANSMISSION CONTROL ECU ASSEMBLY)
  1. Disconnect the L140 vehicle approaching speaker controller connector.

  1. Disconnect the A23 transmission control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L140-11 (SFTP) - A23-20 (IND)
    Always
    Below 1 Ω
    L140-11 (SFTP) or A23-20 (IND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

10.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - VEHICLE APPROACHING SPEAKER ASSEMBLY)
  1. Disconnect the L140 vehicle approaching speaker controller connector.

  1. Disconnect the A69 vehicle approaching speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L140-3 (SP+) - A69-1 (+)
    Always
    Below 1 Ω
    L140-8 (SP-) - A69-2 (-)
    Always
    Below 1 Ω
    L140-3 (SP+) or A69-1 (+) - Body ground
    Always
    10 kΩ or higher
    L140-8 (SP-) or A69-2 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER
  1. Reconnect the L140 vehicle approaching speaker controller connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.

  1. Check the operation by referring to the table below.

    Vehicle Proximity Notification System 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Proximity Sound (Vehicle Stationary)
    Proximity sound (Vehicle stationary)
    OFF or ON
    Produces warning sound when vehicle is stopped



    E289168E03
  1. Check the signal waveform according to the condition(s) in the table below.
    Item
    Condition
    Tool setting
    1 V/DIV., 200 ms./DIV.
    Vehicle condition
    Vehicle approaching speaker operating
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vehicle Approaching Speaker Assembly)

    OK:
    The waveform is displayed as shown in the illustration.



NG
REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)
OK


12.INSPECT VEHICLE APPROACHING SPEAKER ASSEMBLY
  1. Remove the vehicle approaching speaker assembly (Click here).

  1. Inspect the vehicle approaching speaker assembly (Click here).



NG
REPLACE VEHICLE APPROACHING SPEAKER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

13.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    On
    Brake pedal released
    Off



NG
GO TO LIGHTING SYSTEM (Click here)
OK


14.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - STOP LIGHT CONTROL RELAY)
  1. Disconnect the L140 vehicle approaching speaker controller connector.

  1. Disconnect the A28 stop light control relay connector.

  1. Disconnect the A58 brake booster with master cylinder brake actuator (skid control ECU) connector.

  1. Disconnect the R17 rear combination light assembly LH connector.

  1. Disconnect the S18 rear combination light assembly RH connector.

  1. Disconnect the d1 center stop light set connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L140-2 (STP) - A28-1 (OUT)
    Always
    Below 1 Ω
    L140-2 (STP) or A28-1 (OUT) - Body ground
    Always
    10 kΩ or higher
    L140-2 (STP) - A58-6 (STP2)
    Always
    Below 1 Ω
    L140-2 (STP) or A58-6 (STP2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

15.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - COMBINATION METER ASSEMBLY)
  1. Disconnect the L140 vehicle approaching speaker controller connector.

  1. Disconnect the L27 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L140-6 (SPD) - L27-7 (+S)
    Always
    Below 1 Ω
    L140-6 (SPD) or L27-7 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK COMBINATION METER ASSEMBLY
  1. Reconnect the L140 vehicle approaching speaker controller connector.

  1. Reconnect the L27 combination meter assembly connector.



    B232574E18
  1. Check the input waveform.

    1. Remove the combination meter assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal L27-7 (+S) and body ground.

    3. Turn the power switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated
      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

17.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
  1. Disconnect the L140 vehicle approaching speaker controller connector.



    E285131E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L140-12 (OPSW) - Body ground
    Idling*
    8 V or higher
    Power switch on (IG)
    Below 2 V

HINT:
*: Put the engine in inspection mode (Click here).

Text in Illustration 
*a
Front view of wire harness connector
(Vehicle Approaching Speaker Controller)


NG
Go to step 18
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

18.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OIL PRESSURE SWITCH ASSEMBLY)
  1. Disconnect the L140 vehicle approaching speaker controller connector.

  1. Disconnect the D26 engine oil pressure switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L140-12 (OPSW) - D26-1
    Always
    Below 1 Ω
    L140-12 (OPSW) or D26-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY (Click here)