Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

The meter ECU (No. 3 meter circuit plate) receives vehicle speed signals from the skid control ECU via the CAN communication system (CAN No. 1 Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.

HINT:
  1. Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
  2. If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores the DTCs. Troubleshoot the Brake Control System (Click here).


WIRING DIAGRAM


E143765E28


INSPECTION PROCEDURE

NOTICE:
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection .

HINT:
Before starting the following inspection, check tire size and tire air pressure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

    Result:

    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SPEED METER OPERATION)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    OFF, 0, 40, 80, 120, 160 mph*1
    There is a deviation in the values displayed on the speedometer*1
    (Control range → Speedometer display)
    1. 0 → 0
    2. 40 → 39.2 to 42.0
    3. 80 → 79.6 to 82.8
    4. 120 → 120.2 to 123.4
    5. 160 → 160.8 to 164.0
    OFF, 0, 40, 80, 120, 160 km/h*2
    There is a deviation in the values displayed on the speedometer*2
    (Control range → Speedometer display)
    1. 0 → 0
    2. 40 → 38.4 to 42.9
    3. 80 → 78.7 to 83.7
    4. 120 → 119.3 to 124.3
    5. 160 → 159.9 to 164.9

    1. *1: for U.S.A.
    2. *2: except U.S.A.

    OK:
    Speedometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)
OK


3.CHECK BRAKE CONTROL SYSTEM
  1. Check if the brake control system output the DTC (Click here).


Result:

Result
Proceed to
The DTC is not output.
A
The DTC is output.
B



B
GO TO BRAKE CONTROL SYSTEM (Click here)
A


4.READ VALUE USING TECHSTREAM (FR/FL/RR/RL WHEEL SPEED, VEHICLE SPEED METER)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus:

    1. for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Data List.

    2. for Combination Meter: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Almost the same as actual vehicle speed (Speedometer tester)
    -
    FL Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Almost the same as actual vehicle speed (Speedometer tester)
    -
    RR Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Almost the same as actual vehicle speed (Speedometer tester)
    -
    RL Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Almost the same as actual vehicle speed (Speedometer tester)
    -

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 mph (0 km/h), Max.: 199 km/h (124 mph)
    Almost the same as actual vehicle speed (Speedometer tester)
    -

    OK:
    When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

    NG:
    When the Data List values of the ECUs do not match, a signal output error of the skid control ECU or an internal malfunction of the combination meter assembly is suspected.



NG
Go to step 5
OK

GO TO BRAKE CONTROL SYSTEM (Click here)  

5.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
  1. Replace the meter circuit plate with a new or a known good one (Click here).

    OK:
    The operation of the speedometer returns to normal.



NG
Go to step 6
OK

END 

6.REPLACE COMBINATION METER ASSEMBLY (NO.4 METER CIRCUIT PLATE)
  1. Replace the combination meter assembly (No. 4 meter circuit plate) with a new or a known good one (Click here).

    OK:
    The operation of the speedometer returns to normal.



NG
Go to step 7
OK

END 

7.REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE)
  1. Replace the combination meter assembly (No. 3 meter circuit plate) with a new or a known good one (Click here).

    OK:
    The operation of the speedometer returns to normal.



NG
REPLACE SKID CONTROL ECU (Click here)
OK

END