Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor assembly and the occupant classification system.
If the center airbag sensor assembly receives signals from the occupant classification ECU, it determines whether the front passenger airbag and front seat belt pretensioner RH should be operated.
DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1650/32
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit.
  2. Occupant classification system malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat wire RH
  3. Occupant classification system
  4. Center airbag sensor assembly

WIRING DIAGRAM


C167958E13


INSPECTION PROCEDURE

1.CHECK DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the power switch on (IG).

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
OK


2.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and occupant classification ECU. Also check that the connectors that link the front seat wire RH and No. 2 floor wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and occupant classification ECU. Also disconnect the connectors that link the front seat wire RH and No. 2 floor wire.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)


  1. Connect the connectors that link the front seat wire RH and No. 2 floor wire.


    C210652E01

  1. Using SST, connect terminals 12 (FSR+) and 13 (FSR-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (FSR+) - W3-4 (FSR-)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *4
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *5
    Connector B
    *6
    Connector E



NG
Go to step 7
OK


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)


    C169178E08
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (FSR+) - W3-4 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *4
    Connector E



NG
Go to step 8
OK


5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)


    C169178E08
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W3-8 (FSR+) - Body ground
    Power switch on (IG)
    Below 1 V
    W3-4 (FSR-) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *4
    Connector E



NG
Go to step 9
OK


6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)


    C169178E08
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    W3-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *4
    Connector E

    HINT:
    After replacing the center airbag sensor assembly, check for DTCs of the center airbag sensor assembly. If DTC B1650/32 is detected, replace the occupant classification ECU (Click here) and perform "zero point calibration" and "sensitivity check" of the occupant classification system (Click here).



NG
Go to step 10
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

7.CHECK NO. 2 FLOOR WIRE (OPEN)


  1. Disconnect the front seat wire RH from the No. 2 floor wire.


    C210654E01

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SW1-1 (FSR+) - SW1-4 (FSR-)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *6
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *7
    Connector B
    *8
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

8.CHECK NO. 2 FLOOR WIRE (SHORT)


    C210653E01
  1. Disconnect the front seat wire RH from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SW1-1 (FSR+) - SW1-4 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *6
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C210653E01
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Disconnect the front seat wire RH from the No. 2 floor wire.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    SW1-1 (FSR+) - Body ground
    Power switch on (IG)
    Below 1 V
    SW1-4 (FSR-) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *6
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C210653E01
  1. Disconnect the front seat wire RH from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    SW1-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    SW1-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    No. 2 Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Wire RH)
    *6
    Connector C



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH