Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15C0    Short in GPS Antenna

DTC    B15C1    Open in GPS Antenna

for Preparation Click here


DESCRIPTION

This DTC is set when the DCM (Telematics Transceiver) detects an open or a short in the telephone and GPS antenna circuit. The DCM (Telematics Transceiver) receives 1574.42 - 1576.42 MHz radio frequency signal from satellites through the telephone and GPS antenna assembly. The cable is a 50 Ω coaxial cable.

DTC No.
DTC Detection Condition
Trouble Area
B15C0
Current for telephone and GPS antenna assembly is more than malfunction criterion for 10 seconds when power switch is on (IG).
(Short circuit)
  1. DCM (Telematics Transceiver)
  2. Wire harness or connector (Telephone and GPS antenna cord)
  3. Telephone and GPS antenna assembly
B15C1
Current for telephone and GPS antenna assembly is less than malfunction criterion for 10 seconds when power switch is on (IG).
(Open circuit)

HINT:
Refer to "PARTS LOCATION" for the installation location of telephone and GPS antenna cord (Click here).


INSPECTION PROCEDURE

1.CHECK DTC
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Perform "HEALTH CHECK" and check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B15C0 or B15C1 is output
    A
    DTC B15C0 or B15C1 is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT TELEPHONE AND GPS ANTENNA CORDS (INSTRUMENT PANEL WIRE)


    B240674E02
  1. Disconnect the instrument panel wire (antenna cord sub-assembly) connector from the DCM (Telematics Transceiver).

  1. Disconnect the instrument panel wire (antenna cord sub-assembly) connector from the No. 2 antenna cord sub-assembly (antenna cord sub-assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-1
    Always
    Below 1 Ω
    A-2a - B-1a
    Always
    Below 1 Ω
    A-2 - Body ground
    Always
    10 kΩ or higher
    A-2a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (Instrument Panel Wire)



NG
REPLACE INSTRUMENT PANEL WIRE (ANTENNA CORD SUB-ASSEMBLY)
OK


3.INSPECT TELEPHONE AND GPS ANTENNA CORDS (NO. 2 ANTENNA CORD SUB-ASSEMBLY)


    B291913E02
  1. Disconnect the telephone and GPS antenna cord (No. 2 antenna cord sub-assembly) connector from the telephone and GPS antenna cord (No. 4 antenna cord sub-assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C-2 - D-2
    Always
    Below 1 Ω
    C-2a - D-2a
    Always
    Below 1 Ω
    C-2 - Body ground
    Always
    10 kΩ or higher
    C-2a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (No. 2 Antenna Cord Sub-assembly)



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


4.INSPECT TELEPHONE AND GPS ANTENNA CORDS (NO. 4 ANTENNA CORD SUB-ASSEMBLY)


    B291912E02
  1. Disconnect the telephone and GPS antenna cord (No. 4 antenna cord sub-assembly) connector from the telephone and GPS antenna cord (No. 5 antenna cord sub-assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E-5 - F-2
    Always
    Below 1 Ω
    E-5a - F-2a
    Always
    Below 1 Ω
    E-5 - Body ground
    Always
    10 kΩ or higher
    E-5a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (No. 4 Antenna Cord Sub-assembly)



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 4 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


5.INSPECT TELEPHONE AND GPS ANTENNA CORDS (NO. 5 ANTENNA CORD SUB-ASSEMBLY)


    B291911E02
  1. Disconnect the telephone and GPS antenna cord (No. 5 antenna cord sub-assembly) connector from the telephone and GPS antenna assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G-1 - H-5
    Always
    Below 1 Ω
    G-1a - H-5a
    Always
    Below 1 Ω
    G-1 - Body ground
    Always
    10 kΩ or higher
    G-1a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (No. 5 Antenna Cord Sub-assembly)



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 5 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


6.REPLACE TELEPHONE AND GPS ANTENNA ASSEMBLY
  1. Replace the telephone and GPS antenna assembly with a normal one and check if the same problem occurs again (Click here).

    OK:
    The system returns to normal.



NG
Go to step 7
OK

END 

7.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The power switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)