Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

REAR VIEW MONITOR SYSTEM > Image from Camera for Rear View Monitor is Abnormal

for Preparation Click here


DESCRIPTION

  1. The video signal of the rear television camera assembly is transmitted to the navigation ECU sub-assembly*1 or radio and display receiver assembly*2.
    *1: for Navigation Receiver Type or for Radio and Display Type (w/o Daytime Running Light)
    *2: for Radio and Display Type (w/ Daytime Running Light)

WIRING DIAGRAM


E246682E02


INSPECTION PROCEDURE

1.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    for Navigation Receiver Type or for Radio and Display Type (w/o Daytime Running Light)
    A
    for Radio and Display Type (w/ Daytime Running Light)
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the L111 connector from the navigation ECU sub-assembly.

  1. Disconnect the V6 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L111-7 (CA+) - V6-4 (CB+)
    Always
    Below 1 Ω
    L111-8 (V+) - V6-2 (CV+)
    Always
    Below 1 Ω
    L111-15 (CGND) - V6-3 (CGND)
    Always
    Below 1 Ω
    L111-16 (V-) - V6-1 (CV-)
    Always
    Below 1 Ω
    L111-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    L111-8 (V+) - Body ground
    Always
    10 kΩ or higher
    L111-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    L111-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK NAVIGATION ECU SUB-ASSEMBLY


    E216447E14
  1. Reconnect the L111 connector to the navigation ECU sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L111-15 (CGND) - Body ground
    Always
    Below 1 Ω
    L111-16 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L111-7 (CA+) - L111-15 (CGND)
    Power switch on (READY)
    Reverse (R) selected
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU Sub-assembly)

    Result:
    Result
    Proceed to
    OK
    A
    NG (for Navigation System)
    B
    NG (for Audio and Visual System)
    C



B
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)

C
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
A


4.CHECK REAR TELEVISION CAMERA ASSEMBLY
  1. Reconnect the V6 connector to the rear television camera assembly.



    E224383E11
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected.

    OK:
    Waveform is similar to that shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    L111-8 (V+) - L127-7 (GND1)
    Tool Setting
    200 mV/DIV., 50 μs/DIV.
    Condition
    Power switch on (READY), reverse (R) selected

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU sub-assembly)
    *b
    Waveform 1 (camera lens not covered, displaying an image)
    *c
    Waveform 2 (camera lens covered, blacking out the screen)
    *d
    Synchronization Signal
    *e
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the L148 connector from the radio and display receiver assembly.

  1. Disconnect the V6 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L148-7 (CA+) - V6-4 (CB+)
    Always
    Below 1 Ω
    L148-8 (V+) - V6-2 (CV+)
    Always
    Below 1 Ω
    L148-15 (CGND) - V6-3 (CGND)
    Always
    Below 1 Ω
    L148-16 (V-) - V6-1 (CV-)
    Always
    Below 1 Ω
    L148-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    L148-8 (V+) - Body ground
    Always
    10 kΩ or higher
    L148-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    L148-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


    E216447E15
  1. Reconnect the L148 connector to the radio and display receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L148-15 (CGND) - Body ground
    Always
    Below 1 Ω
    L148-16 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L148-7 (CA+) - L148-15 (CGND)
    Within 60 seconds of turning the power switch on (ACC)
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


7.CHECK REAR TELEVISION CAMERA ASSEMBLY


  1. for 8 speakers

    1. Reconnect the V6 connector to the rear television camera assembly.



    2. E224385E03
    3. Check the waveform of the rear television camera assembly using an oscilloscope.

      HINT:
      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

      OK:
      Waveform is similar to that shown in the illustration.

      Item
      Content
      Terminal No. (Symbol)
      L148-8 (V+) - L138-20 (GND1)
      Tool Setting
      200 mV/DIV., 50 μs/DIV.
      Condition
      Power switch on (READY), reverse (R) selected

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Component with harness connected
      (Radio and Display Receiver Assembly)
      *b
      Waveform 1 (camera lens not covered, displaying an image)
      *c
      Waveform 2 (camera lens covered, blacking out the screen)
      *d
      Synchronization Signal
      *e
      Video Waveform



  1. for 6 speakers

    1. Reconnect the V6 connector to the rear television camera assembly.



    2. E224383E12
    3. Check the waveform of the rear television camera assembly using an oscilloscope.

      OK:
      Waveform is similar to that shown in the illustration.

      Item
      Content
      Terminal No. (Symbol)
      L148-8 (V+) - L146-7 (GND1)
      Tool Setting
      200 mV/DIV., 50 μs/DIV.
      Condition
      Power switch on (READY), reverse (R) selected

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Component with harness connected
      (Radio and Display Receiver Assembly)
      *b
      Waveform 1 (camera lens not covered, displaying an image)
      *c
      Waveform 2 (camera lens covered, blacking out the screen)
      *d
      Synchronization Signal
      *e
      Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)