Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

DTC    B2342    Switch Failure

for Preparation Click here


DESCRIPTION

This DTC is output when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the sliding roof switch is stuck for 30 seconds or more.

DTC Code
DTC Detection Condition
Trouble Area
B2342
Sliding roof ECU (sliding roof drive gear sub-assembly) detects sliding roof switch is stuck for 30 seconds or more.
  1. Sliding roof ECU (Sliding roof drive gear sub-assembly)
  2. Sliding roof switch (Map light assembly)
  3. Wire harness or connector

WIRING DIAGRAM

Refer to DTC B2341 .

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization (Click here).

1.READ VALUE USING TECHSTREAM (SLIDING ROOF SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Sliding Roof / Data List.

  1. Read the Data List according to the display on the Techstream.

    Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch Failure(Past)
    Open switch failure signal (Past)/ON or OFF
    ON: Sliding roof open signal failure (Past)
    OFF: Sliding roof open signal not fail (Past)
    -
    Close Switch Failure(Past)
    Close switch failure signal (Past)/ON or OFF
    ON: Sliding roof close signal failure (Past)
    OFF: Sliding roof close signal not fail (Past)
    -
    Open Switch Failure(Current)
    Open switch failure signal (Current)/ON or OFF
    ON: Sliding roof open signal failure (Current)
    OFF: Sliding roof open signal not fail (Current)
    -
    Close Switch Failure(Current)
    Close switch failure signal (Current)/ON or OFF
    ON: Sliding roof close signal failure (Current)
    OFF: Sliding roof close signal not fail (Current)
    -

    OK:
    "OFF" appears on the Techstream screen.



NG
Go to step 2
OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)  

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BODY GROUND)


    B215243E12
  1. Disconnect the sliding roof ECU (sliding roof drive gear sub-assembly) connector.

  1. Disconnect the sliding roof switch (map light assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R23-7 (OPN) - Body ground
    Always
    10 kΩ or higher
    R23-9 (CLS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY))


    B215243E12
  1. Reconnect the sliding roof switch (map light assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R23-7 (OPN) - Body ground
    OPEN switch off
    10 kΩ or higher
    R23-9 (CLS) - Body ground
    CLOSE switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))



NG
REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) (Click here)
OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)