Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. DCM (telematics transceiver)*1
  4. Stereo component amplifier assembly
  1. *1: w/ Manual (SOS) Switch

WIRING DIAGRAM


E230078E14


E226483E09


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly, DCM (telematics transceiver)*1 and speakers.

    1. *1: w/ Manual (SOS) Switch

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-15 (WFR+) - Body ground
    Always
    10 kΩ or higher
    L142-30 (WFR-) - Body ground
    Always
    10 kΩ or higher
    L142-8 (WFL+) - Body ground
    Always
    10 kΩ or higher
    L142-23 (WFL-) - Body ground
    Always
    10 kΩ or higher
    L142-9 (FR+) - Body ground
    Always
    10 kΩ or higher
    L142-24 (FR-) - Body ground
    Always
    10 kΩ or higher
    L142-14 (FL+) - Body ground
    Always
    10 kΩ or higher
    L142-29 (FL-) - Body ground
    Always
    10 kΩ or higher
    L142-12 (RR+) - Body ground
    Always
    10 kΩ or higher
    L142-27 (RR-) - Body ground
    Always
    10 kΩ or higher
    L142-11 (RL+) - Body ground
    Always
    10 kΩ or higher
    L142-26 (RL-) - Body ground
    Always
    10 kΩ or higher
    L142-13 (TWR+) - Body ground
    Always
    10 kΩ or higher
    L142-28 (TWR-) - Body ground
    Always
    10 kΩ or higher
    L142-10 (TWL+) - Body ground
    Always
    10 kΩ or higher
    L142-25 (TWL-) - Body ground
    Always
    10 kΩ or higher

  1. w/ Manual (SOS) Switch
    Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L144-5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    L144-6 (SPO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E21
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N1-1 - N1-2
      Always
      4.6 to 6.6 Ω
      O1-1 - O1-2
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E187205E03
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I4-1 - I4-2
      Always
      3.2 to 4.8 Ω
      I5-1 - I5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT REAR SPEAKER ASSEMBLY


    E219303E22
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P3-1 - P3-2
      Always
      3.2 to 5.2 Ω
      Q3-1 - Q3-2
      Always
      3.2 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E187136E06
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P5-1 - P5-2
      Always
      3.2 to 4.8 Ω
      Q5-1 - Q5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)

  1. Proceed to the next step based on the inspection result.

    Result:
    Condition
    Proceed to
    OK (w/ Manual (SOS) Switch)
    A
    OK (w/o Manual (SOS) Switch)
    B
    NG
    C



B
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

C
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
A


6.INSPECT DCM (TELEMATICS TRANSCEIVER)


    E169849E21
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L144-2 (SPI+) - L144-5 (SPO+)
      Always
      Below 1 Ω
      L144-3 (SPI-) - L144-6 (SPO-)
      Always
      Below 1 Ω
      L144-2 (SPI+) - L144-3 (SPI-)
      Always
      10 kΩ or higher
      L144-5 (SPO+) - L144-6 (SPO-)
      Always
      10 kΩ or higher
      L144-2 (SPI+) - Body ground
      Always
      10 kΩ or higher
      L144-3 (SPI-) - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (DCM (Telematics Transceiver))



NG
REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)