Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B1572    Telephone Microphone Error

for Preparation Click here


DESCRIPTION

This DTC is set when the DCM (Telematics Transceiver) detects a malfunction in the telephone microphone assembly circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1572
Current of MCVD reaches malfunction criteria for 10 seconds while power switch is on (IG).
  1. Wire harness or connector
  2. Telephone microphone assembly
  3. Map light assembly
  4. DCM (Telematics Transceiver)

WIRING DIAGRAM


w/o Sliding Roof:

E192507E31


w/ Sliding Roof:

E192507E32


INSPECTION PROCEDURE

1.CHECK DTC
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Perform "HEALTH CHECK" and check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1572 is output
    A
    DTC B1572 is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE POWER SOURCE)
  1. Remove the map light assembly but do not disconnect the connectors (Click here).



    B234642E04
  1. w/o Sliding Roof:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      U3-5 (MACC) - Body ground
      Power switch on (ACC)
      4 to 6 V

      Text in Illustration 
      *1
      Component with harness connected
      (Map Light Assembly)



    B234643E04
  1. w/ Sliding Roof:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      U13-6 (MACC) - Body ground
      Power switch on (ACC)
      4 to 6 V

      Text in Illustration 
      *1
      Component with harness connected
      (Map Light Assembly)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - MAP LIGHT ASSEMBLY)
  1. Disconnect the L144 DCM (Telematics Transceiver) connector.

  1. Disconnect the U3*1 or U13*2 map light assembly connector.

    1. *1: w/o Sliding Roof
    2. *2: w/ Sliding Roof



    B234644E15
  1. w/o Sliding Roof:

    1. Measure the resistance according to the value(s) in the table below .

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L144-34 (MCI+) - U3-4 (MCO+)
      Always
      Below 1 Ω
      L144-35 (MCI-) - U3-3 (MCO-)
      Always
      Below 1 Ω
      L144-34 (MCI+) - Body ground
      Always
      10 kΩ or higher
      L144-35 (MCI-) - Body ground
      Always
      10 kΩ or higher
      L144-32 (SGND) - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Front view of wire harness connector
      (to DCM (Telematics Transceiver))
      *2
      Front view of wire harness connector
      (to Map Light Assembly)



    B234645E09
  1. w/ Sliding Roof:

    1. Measure the resistance according to the value(s) in the table below .

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L144-34 (MCI+) - U13-5 (MCO+)
      Always
      Below 1 Ω
      L144-35 (MCI-) - U13-4 (MCO-)
      Always
      Below 1 Ω
      L144-34 (MCI+) - Body ground
      Always
      10 kΩ or higher
      L144-35 (MCI-) - Body ground
      Always
      10 kΩ or higher
      L144-32 (SGND) - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Front view of wire harness connector
      (to DCM (Telematics Transceiver))
      *2
      Front view of wire harness connector
      (to Map Light Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a normal one and check if the same problem occurs again (Click here for w/o Sliding Roof, Click here for w/ Sliding Roof).

    OK:
    The system returns to normal.



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END 

5.INSPECT DCM (TELEMATICS TRANSCEIVER) (TELEPHONE MICROPHONE POWER SOURCE)


    B235166E81
  1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L144-33 (MCVD) - Body ground
    Power switch on (ACC)
    4 to 6 V

    Text in Illustration 
    *1
    Component with harness connected
    (DCM (Telematics Transceiver))



NG
Go to step 6
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

6.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The power switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)