Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B1573    Short in Telephone Antenna Circuit

DTC    B15CB    Telematics Transceiver Antenna Disconnected

for Preparation Click here


DESCRIPTION

This DTC is set when the DCM (Telematics Transceiver) detects an open or a short in the telephone and GPS antenna circuit. The DCM (Telematics Transceiver) oscillates and receives 824 - 894 MHz or 1850 - 1990 MHz radio-frequency through the telephone and GPS antenna assembly.

DTC No.
DTC Detection Condition
Trouble Area
B1573
Telephone and GPS antenna assembly impedance is lower than malfunction criterion for 10 seconds when power switch is on (IG).
(Short circuit)
  1. DCM (Telematics Transceiver)
  2. Telephone and GPS antenna assembly
  3. Wire harness or connector (Telephone and GPS antenna cord)
B15CB
Telephone and GPS antenna assembly impedance is higher than malfunction criterion for 10 seconds when power switch is on (IG).
(Open circuit)

HINT:
Refer to "PARTS LOCATION" for the installation location of telephone and GPS antenna cord (Click here).


INSPECTION PROCEDURE

1.CHECK DTC
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Perform "HEALTH CHECK" and check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1573 or B15CB is output
    A
    DTC B1573 or B15CB is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT TELEPHONE AND GPS ANTENNA ASSEMBLY


    B234625E02
  1. Disconnect the telephone and GPS antenna assembly connector from the telephone and GPS antenna cord (No. 5 antenna cord sub-assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 2a
    Always
    4 to 11 kΩ

    Text in Illustration 
    *1
    Telephone and GPS Antenna Assembly



NG
REPLACE TELEPHONE AND GPS ANTENNA ASSEMBLY (Click here)
OK


3.INSPECT TELEPHONE AND GPS ANTENNA CORDS (NO. 5 ANTENNA CORD SUB-ASSEMBLY)


    B291911E01
  1. Disconnect the telephone and GPS antenna cord (No. 5 antenna cord sub-assembly) connector from the telephone and GPS antenna cord (No. 4 antenna cord sub-assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-6
    Always
    Below 1 Ω
    A-2a - B-6a
    Always
    Below 1 Ω
    A-2 - Body ground
    Always
    10 kΩ or higher
    A-2a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (No. 5 Antenna Cord Sub-assembly)



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 5 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


4.INSPECT TELEPHONE AND GPS ANTENNA CORDS (NO. 4 ANTENNA CORD SUB-ASSEMBLY)


    B291912E01
  1. Disconnect the telephone and GPS antenna cord (No. 4 antenna cord sub-assembly) connector from the telephone and GPS antenna cord (No. 2 antenna cord sub-assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C-6 - D-5
    Always
    Below 1 Ω
    C-6a - D-5a
    Always
    Below 1 Ω
    C-6 - Body ground
    Always
    10 kΩ or higher
    C-6a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (No. 4 Antenna Cord Sub-assembly)



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 4 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


5.INSPECT TELEPHONE AND GPS ANTENNA CORDS (NO. 2 ANTENNA CORD SUB-ASSEMBLY)


    B291913E01
  1. Disconnect the telephone and GPS antenna cord (No. 2 antenna cord sub-assembly) connector from the instrument panel wire (antenna cord sub-assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E-5 - F-1
    Always
    Below 1 Ω
    E-5a - F-1a
    Always
    Below 1 Ω
    E-5 - Body ground
    Always
    10 kΩ or higher
    E-5a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (No. 2 Antenna Cord Sub-assembly)



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


6.INSPECT TELEPHONE AND GPS ANTENNA CORDS (INSTRUMENT PANEL WIRE)


    B240675E02
  1. Disconnect the instrument panel wire (antenna cord sub-assembly) cord connector from the DCM (Telematics Transceiver).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G-1 - H-1
    Always
    Below 1 Ω
    G-1a - H-1a
    Always
    Below 1 Ω
    G-1 - Body ground
    Always
    10 kΩ or higher
    G-1a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Telephone and GPS Antenna Cord (Instrument Panel Wire)



NG
REPLACE INSTRUMENT PANEL WIRE (ANTENNA CORD SUB-ASSEMBLY)
OK


7.REPLACE TELEPHONE AND GPS ANTENNA ASSEMBLY
  1. Replace the telephone and GPS antenna assembly with a normal one and check if the same problem occurs again (Click here).

    OK:
    The system returns to normal.



NG
Go to step 8
OK

END 

8.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The power switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)