Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P106A    Evaporative Emission System Pressure Sensor - Manifold Absolute Pressure Correlation

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
P106A
The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and manifold absolute pressure sensor (MAP*) is more than 7.442 kPa (55.82 mmHg)
(2 trip detection logic)
  1. Canister pressure sensor (Built into canister assembly)
  2. Manifold absolute pressure sensor

HINT:
*: Data List Name


MONITOR DESCRIPTION

This DTC is designed to detect a deviation in the output characteristics of a pressure sensor.
The pressure of the canister pressure sensor and manifold absolute pressure sensor is monitored 50 minutes after the power switch is turned off. If there is a difference in the pressures, the MIL is illuminated (2 trip detection logic).

HINT:
Correct judgment may not be possible when the altitude is 13124 ft (4000 m) or more.


MONITOR STRATEGY


Related DTC
P106A: Absolute pressure sensor rationality
Required Sensors/Components (Main)
Canister pressure sensor
Manifold absolute pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
Within 65 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0106, P0107, P0108 (Manifold absolute pressure)
P0401 (EGR system (closed))
P0452, P0453 (Evaporative emission system pressure sensor)
Arrive at after engine stop
50 minutes
Time after ECM started by soak-timer
60 seconds or more
Auxiliary battery voltage
10.5 V or more
Intake air temperature
-10°C (14°F) or more
Engine coolant temperature
-10°C (14°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Difference between EVAP pressure and manifold absolute pressure
More than 7.442 kPa (55.82 mmHg)

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the Clear DTC procedure).
  4. Put the engine in inspection mode (maintenance mode) (Click here) [A].
  5. Start the engine and Idle for 10 seconds.
  6. Turn the power switch off.
  7. Leave the power switch off for 55 minutes [B]
  8. Turn the power switch on (IG) and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P106A.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [C] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P106A)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.


Result 
Result
Proceed to
DTC P106A is output
A
DTC P106A and other DTCs are output
B

HINT:
If any DTCs other than P106A are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (VAPOR PRESSURE PUMP AND MAP)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump and MAP.

  1. Compare the Vapor Pressure Pump and MAP data from the Data List with day's atmospheric pressure*.

    HINT:
    1. *: Standard atmospheric pressure is 101 kPa(abs) [760 mmHg(abs)] at sea level. The atmospheric pressure decreases by approximately 1 kPa (7.5 mmHg) for every 100 m of elevation increase. Atmospheric pressure is also affected by weather conditions.
    2. Also, check "Atmospheric Pressure" in the Data List.
    3. If you do not know the atmospheric pressure refer to the Vapor Pressure Pump value of other vehicles in the workshop and check the difference in pressure.


    Result 
    Result
    Proceed to
    If the Vapor Pressure Pump value differs from the atmospheric pressure by 3.5 kPa (26.25 mmHg) or more
    A
    If the MAP value differs from the atmospheric pressure by 3.5 kPa (26.25 mmHg) or more
    B



B
Go to step 4
A


3.REPLACE CANISTER (CANISTER PUMP MODULE)
  1. Replace the canister (Click here).



NEXT
Go to step 5

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).


NEXT


5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Vapor Pressure Pump.

  1. Confirm that the difference between Vapor Pressure Pump and MAP are 3.5 kPa (26.25 mmHg) or less.


NEXT

END