DTC P261B Engine Coolant Pump "B" Control Malfunction |
DTC P261C Engine Coolant Pump "B" Control Circuit Low |
DTC P261D Engine Coolant Pump "B" Control Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P261B | Engine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1 trip detection logic) |
|
| P261C | Engine water pump assembly output voltage is less than specified value while the engine water pump assembly is operating (1 trip detection logic) |
|
| P261D | Engine water pump assembly output voltage is higher than specified value while the engine water pump assembly is operating (1 trip detection logic) |
|
| Related DTCs | P261B: Engine water pump circuit performance P261C: Engine water pump circuit range check (low voltage) P261D: Engine water pump circuit range check (high voltage) |
| Required Sensors/Components (Main) | Engine water pump assembly |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 15 seconds: Engine coolant pump circuit performance 3 seconds: Engine coolant pump circuit range check (low voltage, high voltage) |
| MIL Operation | Immediately |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | None |
| All of the following conditions are met | - |
| Auxiliary battery voltage | 8 V or more |
| Power switch | On (IG) |
| Time after power switch off to on (IG) | More than 0.5 seconds |
| All of the following conditions are met | - |
| Output duty cycle | 40% or more |
| Monitor synchronism monitor status | Enable |
| Engine coolant temperature | -10°C (14°F) or more |
| Engine coolant temperature sensor circuit fail (P0115, P0117, P0118) | Not detected |
| Engine water pump circuit low voltage fail (P261C) | Not detected |
| Engine water pump circuit high voltage fail (P261D) | Not detected |
| All of the following conditions are met | - |
| Output duty cycle | 40 to 60% |
| Engine water pump circuit performance fail (P261B) | Not detected |
| Engine water pump output terminal voltage monitor counter | 0.08 seconds or more |
| Motor speed | Less than 900 rpm |
| Both of the following conditions are met | - |
| Current engine water pump output terminal voltage | Low |
| Engine water pump output monitor error | Judged |
| Both of the following conditions are met | - |
| Current engine water pump output terminal voltage | High |
| Engine water pump output monitor error | Judged |
| Motor speed | 900 rpm or more |
| Engine water pump output signal | Signal input |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE ELECTRIC WATER PUMP) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Electric Water Pump.
Touch the engine water pump assembly and check that the pump is operating (vibrating).
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM) |
Disconnect the engine water pump assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) - A57-11 (WPI) | Always | Below 1 Ω |
| D13-4 (SWP) - A57-10 (WPO) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) or A57-11 (WPI) - Body ground | Always | 10 kΩ or higher |
| D13-4 (SWP) or A57-10 (WPO) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK ECM (WPI VOLTAGE) |
![]() |
Disconnect the engine water pump assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D13-2 (NWP) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Engine Water Pump Assembly) |
|
| ||||
| OK | ||
| ||
| 4.CHECK ENGINE WATER PUMP ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the engine water pump assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D13-1 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Engine Water Pump Assembly) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND) |
Disconnect the engine water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D13-5 (PGND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM) |
Disconnect the engine water pump assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) - A57-11 (WPI) | Always | Below 1 Ω |
| D13-4 (SWP) - A57-10 (WPO) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) or A57-11 (WPI) - Body ground | Always | 10 kΩ or higher |
| D13-4 (SWP) or A57-10 (WPO) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.REPLACE ENGINE WATER PUMP ASSEMBLY |
Replace the engine water pump assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D) |
Connect the Techstream to the DLC3.
Turn the power switch on.
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble codes.
Read the DTCs.
| Result | Proceed to |
| DTC P261B, P261C or P261D is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 9.INSPECT ENG W/P RELAY |
![]() |
Remove the ENG W/P relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | No auxiliary battery voltage applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - ENGINE WATER PUMP ASSEMBLY) |
Remove the ENG W/P relay from the engine room relay block.
Disconnect the engine water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ENG W/P relay terminal 5 - D13-1 (+B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| ENG W/P relay terminal 5 or D13-1 (+B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.CHECK ENG W/P RELAY (POWER SOURCE) |
![]() |
Remove the ENG W/P relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ENG W/P relay terminal 3 - Body ground | Always | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | ENG W/P Relay |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - BODY GROUND) |
Remove the ENG W/P relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ENG W/P relay terminal 1 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||