Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY

FRONT SEAT SIDE AIRBAG ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)
  1. Temporarily install the separate type front seatback cover with pad to the front seatback spring sub-assembly.



    B229856
  1. Engage the 4 claws to install the 2 front seat headrest supports.



    B301044
  1. Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B301043
  1. Engage the 2 hooks.



    B229852E01
  1. Using hog ring pliers, connect the fastening rubber to the separate type front seatback spring assembly with 3 new hog rings.
    Text in Illustration 
    *1
    Fastening Rubber
    *2
    Hog Ring

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B299241
  1. Close the 2 fasteners.



    B299237
  1. Push in the lower part of 2 fasteners to the separate type front seatback cover as shown in the illustration.



    B299233
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B299229
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)
  1. Temporarily install the separate type front seatback cover with pad to the front seatback spring sub-assembly.



    B229856
  1. Engage the 4 claws and install the 2 front seat headrest supports.



    B302489
  1. Install the separate type front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B299243
  1. Engage the 2 hooks.



    B251969E01
  1. Using hog ring pliers, install the fastening rubber to the front seatback spring with 3 new hog rings.
    Text in Illustration 
    *1
    Fastening Rubber

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B299240
  1. Close the 2 fasteners.



    B299236
  1. Push in the lower part of 2 fasteners to the separate type front seatback cover as shown in the illustration.



    B299233
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B299229
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



4. CONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY WIRE HARNESS
  1. Engage the fastener to secure the front seat side airbag assembly wire harness.

  1. w/ Seat Heater System:

    1. Engage the clamp and connect the seat heater wire harness connector.

  1. Connect the front seat side airbag assembly wire harness to the seat clamp.

  1. Engage the claw and 3 clamps to install the front seat side airbag assembly wire harness.

  1. Connect the rubber band.



5. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect each connector and clamp under the seat.

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B229808E01
  1. Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.



    B229807E01
  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



6. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Connect the cable to the auxiliary negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B251948E01
  1. Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    NOTICE:
    Tighten the bolts in the order indicated in the illustration.

  1. Operate the power seat switch knob and move the seat to the foremost position.



    B251949E01
  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    NOTICE:
    Tighten the bolts in the order indicated in the illustration.



7. INSTALL INNER SEAT TRACK COVER (for Manual Seat)


    B229803
  1. Engage the guide and claw to install the inner seat track cover.



8. INSTALL INNER SEAT TRACK BRACKET COVER (for Power Seat)
  1. Engage the guide and claw to install the inner seat track bracket cover.



9. INSTALL OUTER SEAT TRACK COVER (for Manual Seat)


    B229805
  1. Engage the 2 claws to install the outer seat track cover.



10. INSTALL OUTER SEAT TRACK BRACKET COVER (for Power Seat)
  1. Engage the 2 claws to install the outer seat track bracket cover.



11. INSTALL FRONT SEAT HEADREST ASSEMBLY


12. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL (for Manual Seat)


13. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



14. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



15. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



16. INSPECT FRONT SEAT ASSEMBLY (for Manual Seat)
  1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
    If the seat adjusters do not lock simultaneously, loosen the seat mounting bolts to adjust the adjuster position.

  1. w/ Seat Heater Seat System:
    Check the seat heater operation.

    1. Turn the power switch to on (IG).

    2. Push the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.



17. INSPECT FRONT SEAT ASSEMBLY (for Power Seat)
  1. Check the power seat operation (Click here).

  1. Check the seat heater operation.

    1. Turn the power switch on.

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.



18. ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Seat)
(Click here)


19. PERFORM DIAGNOSTIC SYSTEM CHECK
(Click here)


20. INSPECT SRS WARNING LIGHT
(Click here)