Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/o Daytime Running Light)

DTC    B1579    Voice Recognition Microphone Disconnected

for Preparation Click here


DESCRIPTION

The navigation ECU sub-assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code
DTC Detection Condition
Trouble Area
B1579
Telephone microphone signal is lost.
  1. Map light assembly (telephone microphone assembly)
  2. Navigation ECU sub-assembly
  3. Harness or connector

WIRING DIAGRAM


E245186E05


INSPECTION PROCEDURE

1.INSPECT NAVIGATION ECU SUB-ASSEMBLY


    E237416E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L130-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU Sub-assembly)



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the map light assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-6 (SNS2) - U3-2 (SNS2)
    Always
    Below 1 Ω
    L130-19 (MIN-) - U3-3 (MCO-)
    Always
    Below 1 Ω
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    L130-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-6 (SNS2) - U13-3 (SNS2)
    Always
    Below 1 Ω
    L130-19 (MIN-) - U13-4 (MCO-)
    Always
    Below 1 Ω
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    L130-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    E245346E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    U3-2 (SNS2) - U3-3 (MCO-)
    Always
    Below 1 Ω
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    U13-3 (SNS2) - U13-4 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *a
    Component without harness connected
    (Map Light Assembly (Telephone Microphone Assembly))



NG
Go to step 4
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly (w/ Sliding Roof) (Click here).

  1. Replace the telephone microphone assembly (w/o Sliding Roof) (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END