Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B1579    Voice Recognition Microphone Disconnected

for Preparation Click here


DESCRIPTION

The navigation ECU sub-assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code
DTC Detection Condition
Trouble Area
B1579
Telephone microphone signal is lost.
  1. Map light assembly (telephone microphone assembly)
  2. DCM (telematics transceiver)*1
  3. Navigation ECU sub-assembly
  4. Harness or connector
  1. *1: w/ Manual (SOS) Switch

WIRING DIAGRAM


E245214E01


INSPECTION PROCEDURE

NOTICE:
After replacing the navigation ECU sub-assembly of vehicles subscribed to pay-type satellite radio broadcasts, registration of the XM radio ID is necessary.

1.INSPECT NAVIGATION ECU SUB-ASSEMBLY


    E237416E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L130-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU Sub-assembly)



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK


2.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    w/ Manual (SOS) Switch
    A
    w/o Manual (SOS) Switch
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the DCM (telematics transceiver) connector.

  1. Disconnect the map light assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L144-35 (MCI-) - U3-3 (MCO-)
    Always
    Below 1 Ω
    L144-35 (MCI-) - Body ground
    Always
    10 kΩ or higher
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L144-35 (MCI-) - U13-4 (MCO-)
    Always
    Below 1 Ω
    L144-35 (MCI-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the DCM (telematics transceiver) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L130-19 (MIN-) - L144-19 (MCO-)
    Always
    Below 1 Ω
    L130-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the map light assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-6 (SNS2) - U3-2 (SNS2)
    Always
    Below 1 Ω
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-6 (SNS2) - U13-3 (SNS2)
    Always
    Below 1 Ω
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT DCM (TELEMATICS TRANSCEIVER)
  1. Reconnect the DCM (telematics transceiver) connector.

  1. Reconnect the navigation ECU sub-assembly connector.



    E176672E72
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L144-35 (MCI-) - Body ground
    Always
    Below 1 Ω

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B

    Text in Illustration 
    *a
    Component with harness connected
    (DCM (Telematics Transceiver))



B
Go to step 8
A

REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)  

7.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the map light assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-6 (SNS2) - U3-2 (SNS2)
    Always
    Below 1 Ω
    L130-19 (MIN-) - U3-3 (MCO-)
    Always
    Below 1 Ω
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    L130-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    L130-6 (SNS2) - U13-3 (SNS2)
    Always
    Below 1 Ω
    L130-19 (MIN-) - U13-4 (MCO-)
    Always
    Below 1 Ω
    L130-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    L130-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    E245346E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    U3-2 (SNS2) - U3-3 (MCO-)
    Always
    Below 1 Ω
    w/ Sliding Roof 
    Tester Connection
    Condition
    Specified Condition
    U13-3 (SNS2) - U13-4 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *a
    Component without harness connected
    (Map Light Assembly (Telephone Microphone Assembly))



NG
Go to step 9
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

9.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly (w/ Sliding Roof) (Click here).

  1. Replace the telephone microphone assembly (w/o Sliding Roof) (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END