STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSPECT STEERING COLUMN ASSEMBLY |
![]() |
Check that the 2 bushings are securely installed to the steering column assembly.
If the bushings are deformed, missing or damaged, replace the electric power steering column sub-assembly with a new one.
![]() |
Check that the 2 capsules are securely installed to the electric power steering column sub-assembly as shown in the illustration.
| *1 | Capsule |
| *a | OK |
| *b | NG |
| 2. INSTALL STEERING COLUMN ASSEMBLY |
Install the steering column assembly with the bolt and 2 nuts.
Engage the wire harness clamp.
Connect the 2 connectors to the power steering ECU assembly.
Connect the connectors and engage the wire harness clamps to the steering column assembly.
| 3. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY |
| 4. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY |
| 5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
When reusing the electric power steering column sub-assembly and No. 2 steering intermediate shaft assembly:
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly, and install them.
| *a | Matchmark |
When replacing the electric power steering column sub-assembly or No. 2 steering intermediate shaft assembly:
![]() |
Align the marking (pink) on the steering column assembly shaft with the slit of the No. 2 steering intermediate shaft assembly, and install them.
| *a | Marking (Pink) |
| *b | Slit |
![]() |
Install the bolt while aligning the No. 2 steering intermediate shaft assembly with the position A as shown in the illustration.
| 6. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Install the steering sliding yoke sub-assembly to the No. 2 steering intermediate shaft assembly.
| *a | Matchmark |
Temporarily install the bolt.
| 7. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Install the steering sliding yoke sub-assembly to the steering gear assembly.
| *a | Matchmark |
Install bolt B.
Tighten bolt A.
| 8. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 9. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY |
| 10. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Using pliers, expand the clamp.
While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly and engage the claw.
Return the clamp to its original position.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 11. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Engage the 2 claws to install the upper steering column cover.
| 12. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Engage the 4 claws to install the lower steering column cover.
![]() |
Install the 3 screws.
| 13. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 14. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
![]() |
Rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.
![]() |
Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to align the marks.
| *a | Alignment Mark |
| 15. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft to install the steering wheel assembly.
| *a | Matchmark |
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 16. INSTALL HORN BUTTON ASSEMBLY |
| 17. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT |