Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

DTC    B2285    Steering Lock Position Signal Circuit Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

HINT:
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2285
The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.
  1. AM2 fuse
  2. Steering lock ECU (Steering lock actuator assembly)
  3. Certification ECU (Smart key ECU assembly)
  4. Wire harness or connector
Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait 40 seconds or more with the power switch off (with the steering wheel locked), then turn the power switch on (ACC) (with the steering unlocked) and wait 40 seconds or more.
  1. *: Only detected while a malfunction is present and the power switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The hybrid control system cannot be started.
The ECU does not send an hybrid control system start request.

WIRING DIAGRAM


B284661E09


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body / Power Source Control / DTC.
    for Entry&Start: Body / Entry&Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  5. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  6. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2285
Power Source Control
  1. Steering Unlock Switch
Entry&Start
  1. Power Supply Short
  2. Motor Driver Short
  3. Lock Bar Stuck Error
-

1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
  1. Check for DTCs (Click here).

    OK:
    LIN communication system DTC B2785 is not output simultaneously.

    HINT:
    1. If the steering wheel cannot be locked or unlocked, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.
    2. If LIN communication is not available, the steering wheel cannot be locked or unlocked.



NG
GO TO DTC B2785 (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF
    ON: Steering unlocked
    OFF: Steering locked
    1. When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked.
    2. When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The hybrid control system cannot be started when the steering unlock signal is off.

    Result:
    Result
    Proceed to
    Data List item does not change
    A
    Data List item changes
    B



B
REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (Click here)
A


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E34
  1. Disconnect the G77 connector from the certification ECU (smart key ECU assembly).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G77-2 (+B) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


4.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E35
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G77-11 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


    C197722E69
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Positive (+) tester probe → G50-4 (SLP1)
    Negative (-) tester probe → Body ground
    Steering locked*
    10 kΩ or higher
    Steering unlocked*
    Below 1 Ω

    HINT:
    1. *: If any of the doors are opened then closed with the shift lever in P and the power switch off, the steering wheel will be locked. If the power switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.
    2. DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the certification ECU (smart key ECU assembly) individually.

    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU (Steering Lock Actuator Assembly))



NG
REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
  1. Disconnect the G79 connector from the certification ECU (smart key ECU assembly).

  1. Disconnect the G50 connector from the steering lock ECU (steering lock actuator assembly).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G79-26 (SLP) - G50-4 (SLP1)
    Always
    Below 1 Ω
    G79-26 (SLP) or G50-4 (SLP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)