Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH

for Preparation Click here


DESCRIPTION

When the power switch is on (IG), the power window regulator motor assembly (for rear LH door) is operated by the power window regulator switch assembly (for rear LH door).

WIRING DIAGRAM


B301257E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR) - AUXILIARY BATTERY)
  1. Disconnect the power window regulator switch assembly (for rear LH door) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L1-3 (B) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR)


    B164433E19
  1. Remove the power window regulator switch assembly (for rear LH door) (Click here).

  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (D) - 2 (SD)
    UP
    Below 1 Ω
    3 (B) - 4 (U)
    Below 1 Ω
    1 (D) - 2 (SD)
    off
    Below 1 Ω
    4 (U) - 5 (SU)
    Below 1 Ω
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Switch Assembly (for Rear LH Door))



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR) - POWER WINDOW REGULATOR MOTOR LH)
  1. Disconnect the power window regulator motor assembly (for rear LH door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L1-4 (U) - L2-1 (U)
    Always
    Below 1 Ω
    L1-1 (D) - L2-2 (D)
    Always
    Below 1 Ω
    L1-4 (U) - Body ground
    Always
    10 kΩ or higher
    L1-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B298969E12
  1. Remove the power window regulator master switch assembly (Click here).

  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    6 (B) - 12 (U)
    UP
    Below 1 Ω
    1 (E) - 13 (D)
    Below 1 Ω
    1 (E) - 12 (U)
    off
    Below 1 Ω
    1 (E) - 13 (D)
    Below 1 Ω
    6 (B) - 13 (D)
    DOWN
    Below 1 Ω
    1 (E) - 12 (U)
    Below 1 Ω
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    6 (B) - 18 (U)
    UP
    Below 1 Ω
    9 (E) - 10 (D)
    Below 1 Ω
    9 (E) - 18 (U)
    off
    Below 1 Ω
    9 (E) - 10 (D)
    Below 1 Ω
    6 (B) - 10 (D)
    DOWN
    Below 1 Ω
    9 (E) - 18 (U)
    Below 1 Ω

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR))
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    J1-12 (U) - L1-5 (SU)
    Always
    Below 1 Ω
    J1-13 (D) - L1-2 (SD)
    Always
    Below 1 Ω
    J1-12 (U) - Body ground
    Always
    10 kΩ or higher
    J1-13 (D) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    H1-18 (U) - L1-5 (SU)
    Always
    Below 1 Ω
    H1-10 (D) - L1-2 (SD)
    Always
    Below 1 Ω
    H1-18 (U) - Body ground
    Always
    10 kΩ or higher
    H1-10 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) (Click here)