ELECTRONICALLY CONTROLLED BRAKE SYSTEM > VSC OFF Switch Circuit |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Check if CAN communication system DTCs are output (Click here).
| Result | Proceed to |
| DTCs are not output. | A |
| DTCs are output. | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Select the Data List on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| TRC/VSC Off Mode | TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF | Normal: Normal mode TRC OFF: TRC off mode Unknown: Unspecified VSC OFF: VSC off mode | - |
Check the indicator light and mode condition on the intelligent tester changes according to VSC OFF switch operation.
| Switch Operation | Mode Condition Display | Multi-information Display (TRC OFF message) | VSC OFF Indicator Light |
| Not pressed | Normal | Not displayed | Does not come on |
| Pressing the VSC OFF switch | TRC OFF | Displayed | Does not come on |
| Pressing and holding the VSC OFF switch | VSC OFF | Displayed | Comes on |
| Result | Proceed to |
| Indicator light and mode condition display do not change. | A |
| Mode condition display is normal, but indicator light does not change. | B |
| Indicator light and mode condition display is normal. | C |
|
| ||||
|
| ||||
| A | |
| 4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MULTI-INFORMATION DISPLAY (TRC OFF MESSAGE) AND VSC OFF INDICATOR LIGHT) |
Select the Active Test on the intelligent tester (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| TRC(TRAC) OFF Indicator Light | Multi-information display (TRC OFF message) | Display ON/OFF | Observe combination meter assembly |
| VSC OFF Indicator Light | VSC OFF indicator light | Indicator light ON/OFF | Observe combination meter assembly |
Check the multi-information display (TRC OFF message) and VSC OFF indicator light in the combination meter assembly turns on or off in accordance with intelligent tester operation.
|
| ||||
| OK | |
| 5.INSPECT VSC OFF SWITCH |
![]() |
Turn the power switch off.
Disconnect the VSC OFF switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (+) - 3 (E) | Switch is pushed | Below 1 Ω |
| 6 (+) - 3 (E) | Switch is not pushed | 10 kΩ or higher |
| *a | Component without harness connected (VSC OFF Switch) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH) |
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-8 (CSW) - G83-6 (+) | Always | Below 1 Ω |
| A41-8 (CSW) - Body ground | Always | 10 kΩ or higher |
| G83-3 (E) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 7.INSPECT COMBINATION METER ASSEMBLY |
Turn the power switch off.
Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester (Click here).
Check the combination meter assembly.
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||