Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U0100    Lost Communication with ECM / PCM "A"

DTC    U0129    Lost Communication with Brake System Control Module

DTC    U0293    Lost Communication with HV ECU

for Preparation Click here


DESCRIPTION

  1. The hybrid vehicle control computer assembly communicates with the ECM and brake booster with master cylinder assembly (skid control ECU). When the hybrid vehicle control computer assembly does not receive data from the ECM or brake booster with master cylinder assembly (skid control ECU), the hybrid vehicle control computer assembly stores DTC U0100 or U0129.
  2. The ECM communicates with the hybrid vehicle control computer assembly. When the ECM does not receive data from the hybrid vehicle control computer assembly, the ECM stores DTC U0293.
  3. The brake booster with master cylinder assembly (skid control ECU) communicates with the hybrid vehicle control computer assembly. When the brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control computer assembly, the brake booster with master cylinder assembly (skid control ECU) stores DTC U0293.

DTC No.
DTC Detection Condition
Trouble Area
U0100
The hybrid vehicle control computer assembly does not receive data from the ECM.
  1. Open or short in sub bus 15 main line or connector
  2. Open or short in sub bus 15 branch line or connector
  3. Power source circuit of hybrid vehicle control computer assembly
  4. Hybrid vehicle control computer assembly
  5. Power source circuit of ECM
  6. ECM
  7. Open or short in CAN junction connector LH
U0129
The hybrid vehicle control computer assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU).
  1. Open or short in sub bus 15 main line or connector
  2. Open or short in sub bus 15 branch line or connector
  3. Power source circuit of hybrid vehicle control computer assembly
  4. Hybrid vehicle control computer assembly
  5. Power source circuit of brake booster with master cylinder assembly (skid control ECU)
  6. Brake booster with master cylinder assembly (Skid control ECU)
  7. Open or short in CAN junction connector LH
U0293
  1. The ECM does not receive data from the hybrid vehicle control computer assembly.
  2. The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control computer assembly.
  1. Open or short in sub bus 15 main line or connector
  2. Open or short in sub bus 15 branch line or connector
  3. Power source circuit of ECM
  4. ECM
  5. Power source circuit of hybrid vehicle control computer assembly
  6. Hybrid vehicle control computer assembly
  7. Power source circuit of brake booster with master cylinder assembly (skid control ECU)
  8. Brake booster with master cylinder assembly (Skid control ECU)
  9. Open or short in CAN junction connector LH

HINT:
This diagnosis procedure is for when DTC U0100, U0129 and U0293 are output at the same time.


WIRING DIAGRAM


C251628E11


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT
  1. Reconfirm DTCs.

    HINT:
    If the hybrid vehicle control computer assembly outputs only DTC U0129, troubleshoot DTC U0129 and check the branch circuit of sub bus 15.

    Result:
    Result
    Proceed to
    The hybrid vehicle control computer assembly outputs DTC U0129 and other DTCs.
    (GTS display: Hybrid Control)
    A
    The hybrid vehicle control computer assembly outputs only DTC U0129.
    (GTS display: Hybrid Control)
    B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
A


2.CHECK SUB BUS 15
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C260977E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    G81-31 (CA3P) - G81-30 (CA3N)
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    Below 54 Ω: Short circuit between bus lines
    70 Ω or higher: Open circuit in main bus lines
    G81-31 (CA3P) - G80-6 (E1)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    Below 200 Ω: CANH ground short
    G81-30 (CA3N) - G80-6 (E1)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    Below 200 Ω: CANL ground short
    G81-31 (CA3P) - G81-3 (BATT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Below 6 kΩ: CANH +B short
    G81-30 (CA3N) - G81-3 (BATT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Below 6 kΩ: CANL +B short

    Text in Illustration  
    *a
    Component with harness connected
    (Hybrid Vehicle Control Computer Assembly)

    HINT:
    1. When the values are as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.
    2. If DTCs are output although the bus circuit is normal and DTCs were cleared, replace the hybrid vehicle control computer assembly.

    Result:
    Result
    Proceed to
    OK
    A
    NG (Open circuit in CAN main bus lines)
    B
    NG (Short circuit between bus lines)
    C
    1. NG (Ground short)
    2. NG (+B short)
    D



B
Go to step 3

C
Go to step 7

D
Go to step 12
A

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY (Click here)  

3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY)


    A204446E86
  1. Disconnect the G81 hybrid vehicle control computer assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G81-31 (CA3P) - G81-30 (CA3N)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration  
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control Computer Assembly)



NG
Go to step 4
OK

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY (Click here)  

4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
  1. Reconnect the G81 hybrid vehicle control computer assembly connector.



    C238890E91
  1. Disconnect the G86 CAN junction connector LH (instrument panel wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    G86-10 (CANH) - G86-21 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    Hybrid vehicle control computer assembly

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to CAN Junction Connector LH (Instrument Panel Wire Side))
    *b
    to Hybrid Vehicle Control Computer Assembly



NG
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)
OK


5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
  1. Reconnect the G86 CAN junction connector LH (instrument panel wire side).



    C238890E92
  1. Disconnect the A74 CAN junction connector LH (engine room main wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    A74-3 (CANH) - A74-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    ECM

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to CAN Junction Connector LH (Engine Room Main Wire Side))
    *b
    to ECM



NG
Go to step 6
OK

REPLACE CAN JUNCTION CONNECTOR LH 

6.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN J/C LH)
  1. Reconnect the A74 CAN junction connector LH (engine room main wire side).



    C239823E11
  1. Disconnect the A40 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-12 (CANP) - A40-25 (CANN)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - CAN J/C LH)
OK

REPLACE ECM (Click here)  

7.CHECK FOR SHORT IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)


    A204446E86
  1. Disconnect the G81 hybrid vehicle control computer assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G81-31 (CA3P) - G81-30 (CA3N)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration  
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control Computer Assembly)



NG
Go to step 8
OK

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY (Click here)  

8.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
  1. Reconnect the G81 hybrid vehicle control computer assembly connector.



    C238890E91
  1. Disconnect the G86 CAN junction connector LH (instrument panel wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    G86-10 (CANH) - G86-21 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    Hybrid vehicle control computer assembly

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to CAN Junction Connector LH (Instrument Panel Wire Side))
    *b
    to Hybrid Vehicle Control Computer Assembly



NG
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)
OK


9.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
  1. Reconnect the G86 CAN junction connector LH (instrument panel wire side).



    C238890E94
  1. Disconnect the A74 CAN junction connector LH (engine room main wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    A74-1 (CANH) - A74-12 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    Brake booster with master cylinder assembly (Skid control ECU)
    A74-3 (CANH) - A74-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    ECM

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to CAN Junction Connector LH (Engine Room Main Wire Side))
    *b
    to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    *c
    to ECM

    Result:
    Result
    Proceed to
    OK
    A
    NG (ECM CAN main bus lines)
    B
    NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch lines)
    C



B
Go to step 10

C
Go to step 11
A

REPLACE CAN JUNCTION CONNECTOR LH 

10.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH)
  1. Reconnect the A74 CAN junction connector LH (engine room main wire side).



    C239823E11
  1. Disconnect the A40 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-12 (CANP) - A40-25 (CANN)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - CAN J/C LH)
OK

REPLACE ECM (Click here)  

11.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)
  1. Reconnect the A74 CAN junction connector LH (engine room main wire side).



    C249762E42
  1. Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-35 (CA2H) - A41-34 (CA2L)
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

    Result:
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for RHD) (Click here)

C
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for LHD) (Click here)  

12.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH)


    C258680E78
  1. Disconnect the G86 CAN junction connector LH (instrument panel wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    G86-10 (CANH) - G4-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    Hybrid vehicle control computer assembly
    G86-21 (CANL) - G4-4 (CG)
    G86-10 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Hybrid vehicle control computer assembly
    G86-21 (CANL) - G4-16 (BAT)

    HINT:
    1. It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
    2. Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.

    Text in Illustration  
    *1
    DLC3
    *a
    Front view of wire harness connector
    (to CAN Junction Connector LH (Instrument Panel Wire Side))
    *b
    to Hybrid Vehicle Control Computer Assembly



NG
Go to step 14
OK


13.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH)


    C258680E79
  1. Disconnect the A74 CAN junction connector LH (engine room main wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    A74-1 (CANH) - G4-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    Brake booster with master cylinder assembly (Skid control ECU)
    A74-12 (CANL) - G4-4 (CG)
    A74-3 (CANH) - G4-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    ECM
    A74-14 (CANL) - G4-4 (CG)
    A74-1 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Brake booster with master cylinder assembly (Skid control ECU)
    A74-12 (CANL) - G4-16 (BAT)
    A74-3 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    ECM
    A74-14 (CANL) - G4-16 (BAT)

    HINT:
    1. It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
    2. Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.

    Text in Illustration  
    *1
    DLC3
    *a
    Front view of wire harness connector
    (to CAN Junction Connector LH (Engine Room Main Wire Side))
    *b
    to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    *c
    to ECM

    Result:
    Result
    Proceed to
    OK
    A
    NG (ECM CAN main bus line)
    B
    NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch line)
    C



B
Go to step 15

C
Go to step 16
A

REPLACE CAN JUNCTION CONNECTOR LH 

14.CHECK FOR SHORT IN SUB BUS 15 LINE (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)


    C207841E10
  1. Disconnect the G80 and G81 hybrid vehicle control computer assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G81-31 (CA3P) - G80-6 (E1)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G81-30 (CA3N) - G80-6 (E1)
    G81-31 (CA3P) - G81-3 (BATT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G81-30 (CA3N) - G81-3 (BATT)

    HINT:
    1. It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
    2. Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.

    Text in Illustration  
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control Computer Assembly)



NG
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)
OK

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY (Click here)  

15.CHECK FOR SHORT IN SUB BUS 15 LINE (ECM - CAN J/C LH)


    C258985E02
  1. Disconnect the A40 and C9 or C10 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-12 (CANP) - C9-16 (E1)*1
    A40-12 (CANP) - C10-16 (E1)*2
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A40-25 (CANN) - C9-16 (E1)*1
    A40-25 (CANN) - C10-16 (E1)*2
    A40-12 (CANP) - A40-1 (BATT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A40-25 (CANN) - A40-1 (BATT)

    *1: for RHD
    *2: for LHD

    HINT:
    1. It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
    2. Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.

    Text in Illustration  
    *A
    for RHD
    *B
    for LHD
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN J/C LH)
OK

REPLACE ECM (Click here)  

16.CHECK FOR SHORT IN SUB BUS 15 LINE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)


    C249762E51
  1. Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-35 (CA2H) - A41-28 (GND)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A41-34 (CA2L) - A41-28 (GND)
    A41-35 (CA2H) - A41-14 (BI)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A41-34 (CA2L) - A41-14 (BI)

    HINT:
    1. It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
    2. Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.

    Text in Illustration  
    *a
    Front view of wire harness connector
    (to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

    Result:
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for RHD) (Click here)

C
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for LHD) (Click here)