ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL NO. 1 ENGINE HANGER |
![]() |
Install the 2 No. 1 engine hangers with 2 new bolts.
| Part Name | Part No. |
| No. 1 engine hanger | 12281-21090 |
| Bolt | 91672-81025 |
| 2. INSTALL ENGINE WIRE |
Connect all of the clamps and connectors and install the engine wire from the engine assembly.
| 3. REMOVE ENGINE STAND |
Using a chain block and sling device, secure the engine assembly.
Remove the engine stand from the engine.
| 4. INSTALL ENGINE MOUNTING INSULATOR LH |
Temporarily install the engine mounting insulator LH with the 5 bolts.
![]() |
Tighten the 5 bolts in the sequence shown in the illustration.
Connect the wire harness clamp.
| 5. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.
![]() |
Tighten the 3 bolts in the sequence shown in the illustration.
| 6. INSTALL FLYWHEEL SUB-ASSEMBLY |
Gently place the engine assembly onto wood blocks or equivalent.
Install the flywheel sub-assembly .
| 7. INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY |
Gently place the engine assembly onto wood blocks or equivalent.
Install the transmission input damper assembly .
| 8. INSTALL ENGINE ASSEMBLY |
![]() |
Make sure that the knock pins are installed to the engine.
| *1 | Knock Pin |
Temporarily install the hybrid vehicle transaxle assembly to the engine with the 2 bolts.
Fully tighten the 2 bolts in the order of A and B.
![]() |
Install the 4 bolts.
Engage the claw and install the flywheel housing side cover to the engine.
Install the starter hole heat insulator to the engine with the 2 bolts.
Install the drive shaft heat insulator bracket to the engine with the 2 bolts.
Connect the clamp to the drive shaft heat insulator bracket.
Install the drive shaft heat insulator sub-assembly to the engine and drive shaft heat insulator bracket with the bolt and nut.
![]() |
Install the 2 wire harness clamp brackets and transmission control cable clamp to the hybrid vehicle transaxle assembly with the 3 bolts.
| *1 | Wire Harness Clamp Bracket |
| *2 | Transmission Control Cable Clamp |
![]() |
Connect the 7 clamps, 4 connectors and install the wire harness to the hybrid vehicle transaxle assembly with the 3 bolts.
![]() |
Connect the 4 clamps and No. 2 engine wire.
| 9. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
Using a sling device and chain block, set the engine assembly with transaxle on the engine lifter.
Remove the 2 bolts and 2 No. 1 engine hangers.
Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.
Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the front suspension crossmember can be installed.
By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, temporarily install the front suspension crossmember with the 6 bolts.

| *a | CORRECT | *b | INCORRECT |
| *c | Datum Hole | - | - |
Connect the engine mounting insulator LH with the bolt and nut to the engine assembly.
Connect the engine mounting insulator sub-assembly RH with the bolt and 2 nuts to the engine assembly.
![]() |
Using several steps, uniformly tighten the 6 bolts.
| 10. INSTALL FLYWHEEL HOUSING UNDER COVER |
Install the flywheel housing under cover.
| 11. INSTALL FRONT DRIVE SHAFT ASSEMBLY |
| 12. INSTALL NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY |
Install the No. 2 engine room relay block and No. 2 junction block assembly with the 2 nuts and bolt.
| 13. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum (front) | 41.5 mm (1.64 in.) |
| Minimum (rear) | 38.5 mm (1.52 in.) |
Fully insert 2 new gaskets to the exhaust manifold converter and front exhaust pipe assembly.
![]() |
Using a plastic hammer and wooden block, tap in each new gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.
| *1 | Exhaust Manifold and Front Exhaust Pipe Assembly |
| *2 | Gasket |
| *3 | Wooden Block |
Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.
Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.
![]() |
| *1 | Exhaust Manifold |
| *2 | Front Exhaust Pipe Assembly |
| *3 | Gasket |
| *a | Space between flanges: 8.5 mm (0.335 in.) |
Install the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
![]() |
| *1 | Tail Exhaust Pipe Assembly |
| *2 | Front Exhaust Pipe Assembly |
| *3 | Gasket |
| *a | Space between flanges: 6.5 mm (0.256 in.) |
| 14. INSTALL COMPRESSOR WITH MOTOR ASSEMBLY |
![]() |
Install the compressor with motor assembly with the 3 bolts.
![]() |
Connect the connector <B>.
| *1 | Green-colored Lock |
Connect the connector <A> and slide the green-colored lock in the direction indicated by the arrow in the illustration to lock it securely.
| 15. CONNECT SUCTION HOSE SUB-ASSEMBLY |
Remove the vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.
Install the O-ring onto the suction hose sub-assembly.
Install the suction hose sub-assembly to the compressor with motor assembly with the bolt.
| 16. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
Remove the vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.
Install the O-ring onto the No. 1 cooler refrigerant discharge hose.
Install the No. 1 cooler refrigerant discharge hose to the compressor with motor assembly with the bolt.
| 17. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.
| *a | Lip |
| 18. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Install the steering sliding yoke sub-assembly to the steering gear assembly.
| *a | Matchmark |
Install bolt B.
Tighten bolt A.
| 19. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 20. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
Connect the transmission control cable assembly to the transmission control cable clamp and transmission control cable support.
Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Install the transmission control cable assembly to the transmission control shaft lever with the nut.
| 21. CONNECT ENGINE WIRE (for RHD) |
![]() |
Connect the wire harness clamp.
Connect the engine wire to the engine room main wire.
![]() |
Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.
Connect the wire harness clamp and 2 connectors.
![]() |
Connect the ECM connector and lower the lever.
| 22. CONNECT ENGINE WIRE (for LHD) |
![]() |
Connect the wire harness clamp.
Connect the engine wire to the engine room main wire.
![]() |
Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.
Connect the wire harness clamp and 2 connectors.
![]() |
Connect the 2 wire harness clamps.
Connect the ECM connector and lower the lever.
| 23. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push the tube connector into the pipe until the tube connector makes a "click" sound.
![]() | Push |
| 24. CONNECT FUEL VAPOR FEED HOSE ASSEMBLY |
Connect the fuel vapor feed hose assembly.
| 25. CONNECT HEATER WATER HOSE |
Connect the 2 heater water hoses.
| 26. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose.
| 27. CONNECT NO. 1 RADIATOR HOSE |
![]() |
Connect the No. 1 radiator hose.
| *a | Up |
| *b | for LH Side |
| *c | Do Not Position Hose Clamp Claws In This Area |
| 28. INSTALL INVERTER BRACKET ASSEMBLY |
Temporarily install the inverter bracket assembly with the 4 bolts.
![]() |
Tighten the 4 bolts in the sequence shown in the illustration.
Connect the earth wire with the bolt.
Install the inverter reservoir tank assembly with the 2 bolts.
![]() |
Connect the 2 wire harness clamps.
![]() |
Connect the motor cable protector with the bolt.
| 29. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
Install the air cleaner case sub-assembly with the 2 bolts and grommet.
Install the air cleaner filter element sub-assembly.
| 30. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner hose sub-assembly and lock the hose clamp.
| *a | Engine Side |
| *b | 75° |
Install the air cleaner cap sub-assembly with the 2 clamps.
Connect the wire harness clamp.
Connect the mass air flow meter connector.
Connect the purge VSV.
Connect the ventilation hose.
| 31. INSTALL INVERTER WITH CONVERTER ASSEMBLY |
| 32. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and nut.
Engage the clamp to install the wire harness.
| 33. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and nut.
Engage the 3 clamps to install the wire harness.
| 34. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD) |
Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.
| 35. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD) |
Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.
| 36. INSTALL FRONT AIR SHUTTER SEAL (for LHD) |
Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.
| 37. INSTALL FRONT AIR SHUTTER SEAL (for RHD) |
Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.
| 38. INSTALL INNER COWL TOP TO COWL BRACE (for LHD) |
![]() |
Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.
| 39. INSTALL INNER COWL TOP TO COWL BRACE (for RHD) |
![]() |
Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.
| 40. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 41. ADD COOLANT (for Engine) |
![]() |
Insert the engine drain cock plug.
| *1 | Hose |
Disconnect the hose from the engine drain cock plug.
Install the stop ring.
Tighten the radiator drain cock plug by hand.
![]() |
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Coolant level should be within 20 mm (0.787 in.) from the filler tube end.)
| *a | Filler Tube End |
| *b | Coolant Level |
| *c | 20 mm |
Remove the reserve tank cap.
![]() |
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
| *a | Full Line |
| *b | Low Line |
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the water filler cap sub-assembly and reserve tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 42. ADD COOLANT (for Inverter) |
| DTC Code | Detection Item |
| P0A01-726 | Motor Electronics Coolant Temperature Sensor Circuit Range / Performance |
| P0A04-725 | Motor Electronics Coolant Temperature Sensor Circuit Intermittent |
| P0A08-264 | DC / DC Converter Status Circuit |
| P0A78-284 | Drive Motor "A" Inverter Performance |
| P0A78-286 | Drive Motor "A" Inverter Performance |
| P0A7A-322 | Generator Inverter Performance |
| P0A7A-324 | Generator Inverter Performance |
| P0A93-346 | Inverter Cooling System Performance |
| P0A94-553 | DC / DC Converter Performance |
| P0A94-557 | DC / DC Converter Performance |
| P0AEE-277 | Motor Inverter Temperature Sensor "A" Circuit Range / Performance |
| P0AF1-276 | Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic |
| P0BCD-315 | Generator Inverter Temperature Sensor Circuit Range / Performance |
| P0BD0-314 | Generator Inverter Temperature Sensor Circuit Intermittent / Erratic |
| P0C39-626 | DC / DC Converter Temperature Sensor "A" Range / Performance |
| P0C3C-625 | DC / DC Converter Temperature Sensor "A" Intermittent / Erratic |
| P0C3E-628 | DC / DC Converter Temperature Sensor "B" Range / Performance |
| P0C41-627 | DC / DC Converter Temperature Sensor "B" Intermittent / Erratic |
| P0C73-776 | Motor Electronics Coolant Pump "A" Control Performance |
![]() |
Slowly pour coolant into the reserve tank until it reaches the full line.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Keep the coolant at the full line in the reserve tank to compensate for the drop in coolant level when the air bleeds.
When not using the intelligent tester:
Turn the power switch on (READY). [*1]
Turn the power switch off and add coolant to the full line because the coolant level drops as the air bleeds. [*2]
Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.
After the air is completely bled from the cooling system, tighten the reserve tank cap.
![]() |
Add coolant to the full line of the reserve tank.
| 43. ADD HYBRID TRANSAXLE FLUID |
![]() |
Add transaxle fluid until the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening.
| *1 | Filler Nozzle |
After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)
Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket.
| 44. INSPECT HYBRID TRANSAXLE FLUID |
![]() |
Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
Check that the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)
Check for leaks if the quantity of transaxle fluid is low. (If there are no fluid leaks but the amount of the fluid is insufficient, add fluid .
Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.
| 45. ADD ENGINE OIL |
Add new oil.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil |
|
| API grade SL, SM or SN multigrade engine oil |
|
| Item | Standard Condition |
| Drain and refill with oil filter change | 3.7 liters (3.9 US qts, 3.3 Imp. qts) |
| Drain and refill without oil filter change | 3.4 liters (3.6 US qts, 3.0 Imp. qts) |
| Dry fill | 4.1 liters (4.3 US qts, 3.6 Imp. qts) |
Install the oil filler cap.
| 46. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 47. INSTALL SERVICE PLUG GRIP |
| 48. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 49. WARM UP COMPRESSOR |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 50. INSPECT FOR REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 51. CHECK ENGINE OIL LEVEL |
Put the engine in inspection mode (Click here).
Warm up and stop the engine, then wait for 5 minutes. The oil level should be between the low and full level marks on the engine oil level dipstick. If the engine oil level is low, check for leaks and add oil up to the full level mark.
| 52. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG) and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
| 53. INSPECT FOR COOLANT LEAK (for Engine) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator, engine water pump, front exhaust pipe assembly and engine coolant temperature sensor for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 54. INSPECT FOR COOLANT LEAK (for Inverter) |
Remove the reserve tank cap.
![]() |
Install a radiator cap tester.
Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 18 psi), and then check that the pressure does not drop.
Reinstall the reserve tank cap.
| 55. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK |
| 56. INSPECT FOR OIL LEAK |
| 57. INSPECT FOR EXHAUST GAS LEAK |
| 58. INSPECT IGNITION TIMING |
Put the engine in inspection mode (maintenance mode) (Click here).
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
Enter the following menus: Connect the TC and TE1 / OFF.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Connect the clip of a timing light to the ignition coil wire for No. 1 cylinder.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | DLC3 |
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Inspect the ignition timing at idle.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing at idle.
Confirm that the ignition timing advances when the engine rpm is increased.
Remove the timing light.
| 59. INSPECT ENGINE IDLE SPEED |
Put the engine in inspection mode (maintenance mode) (Click here).
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Inspect the engine idle speed.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
| *a | DLC3 |
Put the engine in inspection mode (maintenance mode) (Click here).
Inspect the engine idle speed.
Disconnect terminal 9 (TAC) of the DLC3.
| 60. INSPECT CO/HC |
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.
Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.
Check the DTCs (Click here).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problem | Possible Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 61. INSPECT AND ADJUST SHIFT LEVER POSITION |
| 62. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 63. CHECK ABS SPEED SENSOR SIGNAL |
| 64. INSTALL ENGINE UNDER COVER RH |
| 65. INSTALL ENGINE UNDER COVER LH |