Home › Engine / Hybrid System › 1NZ-FXE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here


CAUTION:
The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

HINT:
Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly camshaft, No. 2 camshaft, camshaft timing gear assembly, piston sub-assembly or piston ring (Click here).



1. INSTALL NO. 1 ENGINE HANGER


    A214905
  1. Install the 2 No. 1 engine hangers with 2 new bolts.

    Torque:
    44 N*m{ 448 kgf*cm , 32 ft.*lbf }

    Part Name
    Part No.
    No. 1 engine hanger
    12281-21090
    Bolt
    91672-81025



2. INSTALL ENGINE WIRE
  1. Connect all of the clamps and connectors and install the engine wire from the engine assembly.



3. REMOVE ENGINE STAND
  1. Using a chain block and sling device, secure the engine assembly.

    NOTICE:
    1. Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
    2. Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

  1. Remove the engine stand from the engine.



4. INSTALL ENGINE MOUNTING INSULATOR LH

HINT:
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.

  1. Temporarily install the engine mounting insulator LH with the 5 bolts.



    A268018E01
  1. Tighten the 5 bolts in the sequence shown in the illustration.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. Connect the wire harness clamp.



5. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.

  1. Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.



    A270110E01
  1. Tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



6. INSTALL FLYWHEEL SUB-ASSEMBLY
  1. Gently place the engine assembly onto wood blocks or equivalent.

    NOTICE:
    1. Set the engine assembly so that it is horizontal.
    2. To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.
    3. This step should be done while hanging the engine assembly using the sling device and chain block.

  1. Install the flywheel sub-assembly .



7. INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY
  1. Gently place the engine assembly onto wood blocks or equivalent.

    NOTICE:
    1. Set the engine assembly so that it is horizontal.
    2. To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.
    3. This step should be done while hanging the engine assembly using the sling device and chain block.

  1. Install the transmission input damper assembly .



8. INSTALL ENGINE ASSEMBLY


    C249707E01
  1. Make sure that the knock pins are installed to the engine.
    Text in Illustration 
    *1
    Knock Pin

  1. Temporarily install the hybrid vehicle transaxle assembly to the engine with the 2 bolts.

    HINT:
    Temporarily tighten bolt B first.

  1. Fully tighten the 2 bolts in the order of A and B.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

    NOTICE:
    1. Make sure that the wire harness or similar items are not pinched between the contact surfaces.
    2. Do not forcibly pry on the hybrid vehicle transaxle.
    3. Make sure to align the hybrid vehicle transaxle so that the input shaft of the hybrid vehicle transaxle will be inserted straight into the inner splines of the transmission input damper.
    4. Do not apply grease either to the spline or to the input shaft.
    5. When inserting the input shaft of the hybrid vehicle transaxle into the inner splines of the transmission input damper, do not shake the hybrid vehicle transaxle excessively.
    6. When mounting the hybrid vehicle transaxle to the engine, make sure to securely fit the knock pins into the knock holes.
    7. When tightening the bolts, be sure that the mating surfaces of the engine and the hybrid vehicle transaxle assembly are in close contact with one another.

    Bolt Length:
    45 mm (1.77 in.)



    C251452
  1. Install the 4 bolts.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    Bolt Length:
    45 mm (1.77 in.)

  1. Engage the claw and install the flywheel housing side cover to the engine.

  1. Install the starter hole heat insulator to the engine with the 2 bolts.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    Bolt Length:
    45 mm (1.77 in.)

  1. Install the drive shaft heat insulator bracket to the engine with the 2 bolts.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    Bolt Length:
    45 mm (1.77 in.)

  1. Connect the clamp to the drive shaft heat insulator bracket.

  1. Install the drive shaft heat insulator sub-assembly to the engine and drive shaft heat insulator bracket with the bolt and nut.

    Torque:
    18 N*m{ 179 kgf*cm , 13 ft.*lbf }



    C249795E02
  1. Install the 2 wire harness clamp brackets and transmission control cable clamp to the hybrid vehicle transaxle assembly with the 3 bolts.
    Text in Illustration 
    *1
    Wire Harness Clamp Bracket
    *2
    Transmission Control Cable Clamp

    Torque:
    Bolt A:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }
    Bolt B:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C249808
  1. Connect the 7 clamps, 4 connectors and install the wire harness to the hybrid vehicle transaxle assembly with the 3 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



    C249812
  1. Connect the 4 clamps and No. 2 engine wire.



9. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
  1. Using a sling device and chain block, set the engine assembly with transaxle on the engine lifter.

    NOTICE:
    1. Place the height adjustment attachment and plate lift attachment so that the engine assembly with transaxle is level.
    2. Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
    3. To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.
    4. Do not place any attachments onto the drain plug and rear cover plug of the hybrid vehicle transaxle assembly.
    5. Make sure to support the engine assembly with transaxle securely to prevent it from falling.

  1. Remove the 2 bolts and 2 No. 1 engine hangers.

  1. Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.

    CAUTION:
    Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.

  1. Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the front suspension crossmember can be installed.



  1. By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, temporarily install the front suspension crossmember with the 6 bolts.


    A268628E01


    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT
    *c
    Datum Hole
    -
    -
    SST
    09670-00010  

  1. Connect the engine mounting insulator LH with the bolt and nut to the engine assembly.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. Connect the engine mounting insulator sub-assembly RH with the bolt and 2 nuts to the engine assembly.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



    A268012E01
  1. Using several steps, uniformly tighten the 6 bolts.

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt B:
    151 N*m{ 1539 kgf*cm , 111 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }



10. INSTALL FLYWHEEL HOUSING UNDER COVER
  1. Install the flywheel housing under cover.



11. INSTALL FRONT DRIVE SHAFT ASSEMBLY
(Click here)


12. INSTALL NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY
  1. Install the No. 2 engine room relay block and No. 2 junction block assembly with the 2 nuts and bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



13. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum (front)
    41.5 mm (1.64 in.)
    Minimum (rear)
    38.5 mm (1.52 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Fully insert 2 new gaskets to the exhaust manifold converter and front exhaust pipe assembly.



    A181728E17
  1. Using a plastic hammer and wooden block, tap in each new gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.
    Text in Illustration 
    *1
    Exhaust Manifold and Front Exhaust Pipe Assembly
    *2
    Gasket
    *3
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gaskets.
    2. Do not reuse the gaskets.
    3. Do not damage the gaskets.
    4. Do not push in the gaskets by using the exhaust pipe when connecting it.

  1. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.



  1. Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    HINT:
    A258941E01
    After installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
    Text in Illustration 
    *1
    Exhaust Manifold
    *2
    Front Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 8.5 mm (0.335 in.)



  1. Install the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    HINT:
    A258966E01
    After installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
    Text in Illustration 
    *1
    Tail Exhaust Pipe Assembly
    *2
    Front Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 6.5 mm (0.256 in.)



14. INSTALL COMPRESSOR WITH MOTOR ASSEMBLY


    E234975E01
  1. Install the compressor with motor assembly with the 3 bolts.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



    E234972E01
  1. Connect the connector <B>.
    Text in Illustration 
    *1
    Green-colored Lock

  1. Connect the connector <A> and slide the green-colored lock in the direction indicated by the arrow in the illustration to lock it securely.

    CAUTION:
    Make sure to wear insulating gloves.

    NOTICE:
    Make sure that the connector is connected securely.



15. CONNECT SUCTION HOSE SUB-ASSEMBLY
  1. Remove the vinyl tape from the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring onto the suction hose sub-assembly.

  1. Install the suction hose sub-assembly to the compressor with motor assembly with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



16. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
  1. Remove the vinyl tape from the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the O-ring onto the No. 1 cooler refrigerant discharge hose.

  1. Install the No. 1 cooler refrigerant discharge hose to the compressor with motor assembly with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



17. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C251686E02
  1. Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.
    Text in Illustration 
    *a
    Lip

    NOTICE:
    Make sure that the lip of the No. 1 steering column hole cover sub-assembly is not damaged.



18. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY


    C249572E03
  1. Install the steering sliding yoke sub-assembly to the steering gear assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    1. Align the matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.
    2. When the steering sliding yoke sub-assembly is replaced with a new one, it has no matchmarks, so install it while the head of the bolt B faces the back of the vehicle.

  1. Install bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



19. INSTALL COLUMN HOLE COVER SILENCER SHEET


    C248046
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



20. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Connect the transmission control cable assembly to the transmission control cable clamp and transmission control cable support.

  1. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

  1. Install the transmission control cable assembly to the transmission control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



21. CONNECT ENGINE WIRE (for RHD)


    A268668
  1. Connect the wire harness clamp.

  1. Connect the engine wire to the engine room main wire.



    A268003
  1. Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.

  1. Connect the wire harness clamp and 2 connectors.



    A268669
  1. Connect the ECM connector and lower the lever.

    NOTICE:
    1. When connecting the connector, make sure that dirt, water or other foreign matter does not become stuck between the connector and other part.
    2. Make sure that the lever is securely locked.



22. CONNECT ENGINE WIRE (for LHD)


    A268668
  1. Connect the wire harness clamp.

  1. Connect the engine wire to the engine room main wire.



    A268004
  1. Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.

  1. Connect the wire harness clamp and 2 connectors.



    A268670
  1. Connect the 2 wire harness clamps.

  1. Connect the ECM connector and lower the lever.

    NOTICE:
    1. When connecting the connector, make sure that dirt, water or other foreign matter does not become stuck between the connector and other part.
    2. Make sure that the lever is securely locked.



23. CONNECT FUEL TUBE SUB-ASSEMBLY


    A264998E01
  1. Push the tube connector into the pipe until the tube connector makes a "click" sound.
    Text in Illustration 
    V100135
    Push

    NOTICE:
    1. Before connecting the fuel tube connector and fuel delivery pipe, check that there is no damage or foreign matter on the connecting part of the fuel delivery pipe.
    2. After connecting the fuel tube connector and fuel delivery pipe, check that they are securely connected by trying to pull them apart.



24. CONNECT FUEL VAPOR FEED HOSE ASSEMBLY
  1. Connect the fuel vapor feed hose assembly.



25. CONNECT HEATER WATER HOSE
  1. Connect the 2 heater water hoses.



26. CONNECT NO. 2 RADIATOR HOSE
  1. Connect the No. 2 radiator hose.



27. CONNECT NO. 1 RADIATOR HOSE


    A275234E01
  1. Connect the No. 1 radiator hose.
    Text in Illustration 
    *a
    Up
    *b
    for LH Side
    *c
    Do Not Position Hose Clamp Claws In This Area

    HINT:
    Make sure that the claws on the hose clamp are positioned as shown in the illustration.



28. INSTALL INVERTER BRACKET ASSEMBLY

CAUTION:
Wear insulated gloves.

  1. Temporarily install the inverter bracket assembly with the 4 bolts.



    A268009E01
  1. Tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Install the inverter reservoir tank assembly with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    A268006
  1. Connect the 2 wire harness clamps.



    A268005
  1. Connect the motor cable protector with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



29. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner case sub-assembly with the 2 bolts and grommet.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the air cleaner filter element sub-assembly.



30. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A267399E01
  1. Install the air cleaner hose sub-assembly and lock the hose clamp.
    Text in Illustration 
    *a
    Engine Side
    *b
    75°

    NOTICE:
    1. Align the groove of the air cleaner hose with the tab of the throttle body with motor assembly and install the hose.
    2. Make sure that the tab of the air cleaner hose clamp stays within the range shown by *b.

  1. Install the air cleaner cap sub-assembly with the 2 clamps.

  1. Connect the wire harness clamp.

  1. Connect the mass air flow meter connector.

  1. Connect the purge VSV.

  1. Connect the ventilation hose.



31. INSTALL INVERTER WITH CONVERTER ASSEMBLY
(Click here)


32. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C250015E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the clamp to install the wire harness.



33. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C249838E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the 3 clamps to install the wire harness.



34. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



35. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



36. INSTALL FRONT AIR SHUTTER SEAL (for LHD)
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



37. INSTALL FRONT AIR SHUTTER SEAL (for RHD)
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



38. INSTALL INNER COWL TOP TO COWL BRACE (for LHD)


    C250011E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



39. INSTALL INNER COWL TOP TO COWL BRACE (for RHD)


    C249834E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



40. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


41. ADD COOLANT (for Engine)


    A267961E01
  1. Insert the engine drain cock plug.
    Text in Illustration 
    *1
    Hose

  1. Disconnect the hose from the engine drain cock plug.

  1. Install the stop ring.

  1. Tighten the radiator drain cock plug by hand.



    A206788E05
  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Coolant level should be within 20 mm (0.787 in.) from the filler tube end.)
    Text in Illustration 
    *a
    Filler Tube End
    *b
    Coolant Level
    *c
    20 mm

    Standard Capacity:
    4.5 liters (4.8 US qts, 4 lmp. qts)

    NOTICE:
    Never use water as a substitute for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Remove the reserve tank cap.



    A275622E01
  1. Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
    Text in Illustration 
    *a
    Full Line
    *b
    Low Line

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the water filler cap sub-assembly and reserve tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to the low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

    2. Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the cooling fan.

      NOTICE:
      1. Make sure that the radiator reserve tank assembly still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reserve tank assembly does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reserve tank assembly is filled to the full line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the full line on the radiator reserve tank assembly.



42. ADD COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign matter.
  2. If the vehicle is driven with air in the inverter cooling system, damage may occur and the following DTCs may be stored.

    DTC Code
    Detection Item
    P0A01-726
    Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
    P0A04-725
    Motor Electronics Coolant Temperature Sensor Circuit Intermittent
    P0A08-264
    DC / DC Converter Status Circuit
    P0A78-284
    Drive Motor "A" Inverter Performance
    P0A78-286
    Drive Motor "A" Inverter Performance
    P0A7A-322
    Generator Inverter Performance
    P0A7A-324
    Generator Inverter Performance
    P0A93-346
    Inverter Cooling System Performance
    P0A94-553
    DC / DC Converter Performance
    P0A94-557
    DC / DC Converter Performance
    P0AEE-277
    Motor Inverter Temperature Sensor "A" Circuit Range / Performance
    P0AF1-276
    Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic
    P0BCD-315
    Generator Inverter Temperature Sensor Circuit Range / Performance
    P0BD0-314
    Generator Inverter Temperature Sensor Circuit Intermittent / Erratic
    P0C39-626
    DC / DC Converter Temperature Sensor "A" Range / Performance
    P0C3C-625
    DC / DC Converter Temperature Sensor "A" Intermittent / Erratic
    P0C3E-628
    DC / DC Converter Temperature Sensor "B" Range / Performance
    P0C41-627
    DC / DC Converter Temperature Sensor "B" Intermittent / Erratic
    P0C73-776
    Motor Electronics Coolant Pump "A" Control Performance



    A266683
  1. Slowly pour coolant into the reserve tank until it reaches the full line.

    Coolant quantity:
    1.6 liters (1.7 US qts, 1.4 Imp. qts.)

    NOTICE:
    To prevent foreign matter such as dust or dirt from entering the cooling system, make sure to confirm that the container used to add coolant is clean and free of foreign matter such as dust or dirt.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

    4. Keep the coolant at the full line in the reserve tank to compensate for the drop in coolant level when the air bleeds.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      1. If free spinning of the inverter water pump is detected for approximately 5 seconds, fail-safe control will be activated to suspend the operation of the pump for approximately 15 seconds and resume operation for approximately 4 seconds repeatedly. Operation of the inverter water pump will return to normal if coolant is added.
      2. A loud noise made by the inverter water pump assembly and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. When not using the intelligent tester:

    1. Turn the power switch on (READY). [*1]

    2. Turn the power switch off and add coolant to the full line because the coolant level drops as the air bleeds. [*2]

      NOTICE:
      1. Be sure to turn the power switch off before adding SLLC.
      2. Do not work on the components in the engine compartment while the vehicle is in the READY-on state because the engine is in intermittent operation.

    3. Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      A loud noise made by the inverter water pump assembly and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. After the air is completely bled from the cooling system, tighten the reserve tank cap.



    A266683
  1. Add coolant to the full line of the reserve tank.



43. ADD HYBRID TRANSAXLE FLUID


    C249713E01
  1. Add transaxle fluid until the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening.
    Text in Illustration 
    *1
    Filler Nozzle

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Use Toyota Genuine ATF WS.
    3. Be sure to fully insert the filler nozzle into the filler plug opening.
    4. Be sure to add fluid slowly. If fluid is added quickly, the fluid may hit internal parts and bounce back, resulting in fluid coming out of the filler plug opening.
    5. Be sure to directly check that the transaxle fluid level is within the specified range.
    6. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.

    Reference:
    3.3 liters (3.5 US qts, 2.9 Imp. qts)

  1. After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    After adding fluid, make sure to check the fluid level.

  1. Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket.

    HINT:
    Because the filler plug will be removed again, the gasket can be reused at this time.



44. INSPECT HYBRID TRANSAXLE FLUID


    C249714
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.

  1. Check that the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Be sure to directly check that the transaxle fluid level is within the specified range.
    3. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.
    4. If the fluid was replaced or fluid was added, make sure to recheck the fluid level after driving the vehicle.

  1. Check for leaks if the quantity of transaxle fluid is low. (If there are no fluid leaks but the amount of the fluid is insufficient, add fluid .

  1. Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



45. ADD ENGINE OIL
  1. Add new oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil
    1. 0W-20
    2. 5W-20
    3. 5W-30
    4. 10W-30
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    2. 20W-50

    Standard Oil Capacity:
    Item
    Standard Condition
    Drain and refill with oil filter change
    3.7 liters (3.9 US qts, 3.3 Imp. qts)
    Drain and refill without oil filter change
    3.4 liters (3.6 US qts, 3.0 Imp. qts)
    Dry fill
    4.1 liters (4.3 US qts, 3.6 Imp. qts)

  1. Install the oil filler cap.



46. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



47. INSTALL SERVICE PLUG GRIP
(Click here)


48. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump or appropriate equipment.



  1. Charge the air conditioning system with refrigerant.

    Refrigerant type:
    HFC-134a (R134a)



    E247093E06


    Text in Illustration 
    *a
    Standard Charge Amount
    *b
    Mean Value in Proper Range
    *c
    Overcharged
    *d
    High Pressure
    *e
    Sub-cool System
    *f
    Refrigerant Amount
    *g
    +/-50 g (+/-1.76 oz)
    -
    -

    Standard charge amount:
    370 to 470 g (13.0 to 16.6 oz)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
    2. The refrigerant amount should be checked by quantity (weight).
    3. The graph above is shown for reference only.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



49. WARM UP COMPRESSOR
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).



50. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Turn the power switch off.
    2. Ensure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).
    3. Repeat the inspection 2 or 3 times.
    4. Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.
      Pressure when the compressor is off: approx. 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)



    I042222E40
  1. Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Inspect for Leak



    N014519E08
  1. Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *2
    Drain Hose

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. Bring the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.

  1. If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.

  1. Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.

    HINT:
    When checking for leaks, the presence of oily dirt at a joint can indicate a leak.



51. CHECK ENGINE OIL LEVEL
  1. Put the engine in inspection mode (Click here).

  1. Warm up and stop the engine, then wait for 5 minutes. The oil level should be between the low and full level marks on the engine oil level dipstick. If the engine oil level is low, check for leaks and add oil up to the full level mark.

    NOTICE:
    Do not fill with engine oil to above the full level mark.



52. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG) and turn the intelligent tester on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



53. INSPECT FOR COOLANT LEAK (for Engine)

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A268671
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator, engine water pump, front exhaust pipe assembly and engine coolant temperature sensor for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



54. INSPECT FOR COOLANT LEAK (for Inverter)
  1. Remove the reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the reserve tank cap while the coolant for the inverter is still hot.



    A266680
  1. Install a radiator cap tester.

  1. Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 18 psi), and then check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator, inverter water pump assembly, inverter with converter, and hybrid vehicle transaxle assembly for leaks.

  1. Reinstall the reserve tank cap.



55. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK


56. INSPECT FOR OIL LEAK


57. INSPECT FOR EXHAUST GAS LEAK


58. INSPECT IGNITION TIMING
  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Warm up and stop the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Put the engine in inspection mode (maintenance mode) (Click here).

    3. Start the engine.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

      Standard ignition timing:
      12 to 16 degrees BTDC

      NOTICE:
      1. Check the ignition timing with the cooling fan off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Check that the ignition timing advances immediately when the engine speed is increased.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

    7. Monitor IGN Advance of the Data List.

      Standard ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Check the ignition timing with the cooling fan off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    8. Enter the following menus: Connect the TC and TE1 / OFF.

    9. Turn the power switch off.

    10. Turn the intelligent tester off.

    11. Disconnect the intelligent tester from the DLC3.



  1. When not using the intelligent tester:



      A266917
    1. Connect the clip of a timing light to the ignition coil wire for No. 1 cylinder.

      NOTICE:
      Use a timing light that detects the primary signal.



    2. A122830E40
    3. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      Text in Illustration 
      *a
      DLC3

      SST
      09843-18040  

      NOTICE:
      Confirm the terminals before connecting them. Connecting the wrong terminals may result in damage to electrical components.

    4. Put the engine in inspection mode (maintenance mode) (Click here).

    5. Start the engine.

    6. Inspect the ignition timing at idle.

      Standard ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Check the ignition timing with the cooling fan off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.

    7. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    8. Inspect the ignition timing at idle.

      Standard ignition timing:
      12 to 16 degrees BTDC

      NOTICE:
      1. Check the ignition timing with the cooling fan off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.

    9. Confirm that the ignition timing advances when the engine rpm is increased.

    10. Remove the timing light.



59. INSPECT ENGINE IDLE SPEED
  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Warm up and stop the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Put the engine in inspection mode (maintenance mode) (Click here).

    3. Start the engine.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the engine idle speed.

      Standard idle speed:
      950 to 1050 rpm

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the idle speed with the cooling fan off.
      3. When checking the idle speed, the transaxle should be in neutral or park.

    6. Turn the power switch off.

    7. Turn the intelligent tester off.

    8. Disconnect the intelligent tester from the DLC3.



  1. When not using the intelligent tester:



      A122830E41
    1. Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
      Text in Illustration 
      *a
      DLC3

      SST
      09843-18030  

    2. Put the engine in inspection mode (maintenance mode) (Click here).

    3. Inspect the engine idle speed.

      Standard idle speed:
      950 to 1050 rpm

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the idle speed with the cooling fan off.
      3. When checking the idle speed, the transaxle should be in neutral or park.

    4. Disconnect terminal 9 (TAC) of the DLC3.



60. INSPECT CO/HC

HINT:
This check determines whether or not the idle CO / HC complies with regulations.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.

  1. Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.

    HINT:
    When doing a 2 mode (with the engine idling/ running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.
    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.


    1. Check the DTCs (Click here).

    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problem
      Possible Cause
      Normal
      High
      Rough idle
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaks from intake and exhaust valves
      4. Leaks from cylinders
      5. Faulty EGR
      Low
      High
      Rough idle (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
      2. Lean mixture causing misfire
      3. Faulty EGR
      High
      High
      Rough idle (Black smoke from exhaust)
      1. Restricted air cleaner filter element
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Throttle body
      4. Faulty EGR



61. INSPECT AND ADJUST SHIFT LEVER POSITION
(Click here)


62. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


63. CHECK FOR SPEED SENSOR SIGNAL
(Click here)


64. INSTALL ENGINE UNDER COVER RH


65. INSTALL ENGINE UNDER COVER LH