ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT COOLANT (for Engine) |
| 2. INSPECT ENGINE OIL |
| 3. INSPECT AUXILIARY BATTERY |
| 4. INSPECT SPARK PLUG |
| 5. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner cap.
Remove the air cleaner filter element.
Visually check that the air cleaner filter element is not excessively damaged or oily.
If necessary, replace the air cleaner filter element.
Install the air cleaner filter element.
Install the air cleaner cap.
| 6. INSPECT IGNITION TIMING |
Put the engine in inspection mode (maintenance mode) (Click here).
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
Enter the following menus: Connect the TC and TE1 / OFF.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Connect the clip of a timing light to the ignition coil wire for No. 1 cylinder.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | DLC3 |
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Inspect the ignition timing at idle.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing at idle.
Confirm that the ignition timing advances when the engine rpm is increased.
Remove the timing light.
| 7. INSPECT ENGINE IDLE SPEED |
Put the engine in inspection mode (maintenance mode) (Click here).
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Inspect the engine idle speed.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
| *a | DLC3 |
Put the engine in inspection mode (maintenance mode) (Click here).
Inspect the engine idle speed.
Disconnect terminal 9 (TAC) of the DLC3.
| 8. INSPECT COMPRESSION |
Put the engine in inspection mode (maintenance mode) (Click here).
Warm up and stop the engine.
Remove the 4 spark plugs (Click here).
![]() |
Insert a compression gauge into the spark plug hole.
Connect the intelligent tester to the DLC3.
Turn the power switch to ON (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Compression Test / ON.
Depress and hold the brake pedal, and turn the power switch to ON (READY).
Install the 4 spark plugs (Click here).
Clear the DTCs (Click here).
| 9. INSPECT CO/HC |
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.
Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.
Check the DTCs (Click here).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problem | Possible Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|