Home › Vehicle Exterior › WIPER / WASHER › WASHER NOZZLE (for Front Side)

WASHER NOZZLE (for Front Side) > INSTALLATION

for Preparation Click here



1. INSTALL WASHER NOZZLE SUB-ASSEMBLY
  1. Engage the 2 claws to install the washer nozzle sub-assembly.

    HINT:
    Use the same procedure for the LH side and RH side.

  1. Connect the washer hose to the washer nozzle sub-assembly.

    HINT:
    Use the same procedure for the LH side and RH side.



2. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 8 guides as shown in the illustration.


    E237534



  1. Engage the 3 guides and 5 claws to install the cowl top ventilator louver sub-assembly as shown in the illustration.


    E237532

  1. Connect the washer hose.

  1. Install the 2 clips.



3. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E237492E01
  1. When reusing the front wiper arm and blade assembly LH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



  1. for LHD:



      E237546E01
    1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

      Text in Illustration 
      *1
      Ceramic Dot

      HINT:
      Hold the wiper arm by hand while tightening the nut.



  1. for RHD:



      E237491E01
    1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

      Text in Illustration 
      *1
      Ceramic Dot

      HINT:
      Hold the wiper arm by hand while tightening the nut.



4. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E237492E01
  1. When reusing the front wiper arm and blade assembly RH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



  1. for LHD:



      E237547E01
    1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

      Text in Illustration 
      *1
      Ceramic Dot

      HINT:
      Hold the wiper arm by hand while tightening the nut.



  1. for RHD:



      E237493E01
    1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

      Text in Illustration 
      *1
      Ceramic Dot

      HINT:
      Hold the wiper arm by hand while tightening the nut.

  1. Turn the power switch on (IG).

  1. Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.

  1. Lift each wiper arm twice after the wipers stop and check the wiper set position.

  1. Turn the power switch off.



5. INSTALL FRONT WIPER ARM HEAD CAP


    E237524
  1. Engage the 3 claws to install the front wiper arm head cap.

    HINT:
    Use the same procedure for the RH side and LH side.



6. INSPECT WASHER NOZZLE SUB-ASSEMBLY
(Click here)


7. ADJUST WASHER NOZZLE SUB-ASSEMBLY
(Click here)


8. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


  1. Clean the front fender to cowl side seal LH (if reusing the front fender to cowl side seal LH).

    1. Remove the double-sided tape from the front fender to cowl side seal LH.

    2. Wipe off any tape adhesive residue with cleaner.

    3. Coat the installation surface on the front fender to cowl side seal LH with primer N-200.

      NOTICE:
      1. Allow the primer to dry for 10 minutes or more.
      2. If 24 hours have elapsed since the primer was applied, reapply primer N-200.



    4. E246046E01
    5. Apply new double-sided tape to the front fender to cowl side seal LH.
      Text in Illustration 
      *1
      Double-sided Tape
      *a
      Edge of Curved Surface
      Item
      Dimension
      A
      0.5 mm (0.0197 in.)
      B
      5.0 mm (0.197 in.)
      C
      45.0 mm (1.77 in.)
      D
      1.0 mm (0.0394 in.)
      E
      2.0 mm (0.0787 in.)

  1. Clean the outside windshield moulding.

    1. Remove the double-sided tape from the outside windshield moulding.

    2. Wipe off any tape adhesive residue with cleaner

    3. Coat the installation surface on the outside windshield moulding with primer N-200.

      NOTICE:
      1. Allow the primer to dry for 10 minutes or more.
      2. If 24 hours have elapsed since the primer was applied, reapply primer N-200.



  1. Install the front fender to cowl side seal LH.

    1. Install the clip to the front fender to cowl side seal LH (if reusing the front fender to cowl side seal LH).

    2. Engage the 2 guides and clip to install the front fender to cowl side seal LH as shown in the illustration.



    3. E237528E01
    4. Remove the release paper from the double-sided tape on the front fender to cowl side seal LH.
      Text in Illustration 
      *1
      Double-sided Tape

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    5. Install the front fender to cowl side seal LH.



9. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure as for the LH side.