Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0225119 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1273 Sliding Roof ECU Communication Stop No communication between sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Sliding roof ECU (sliding roof drive gear sub-assembly)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

S/ROOF fuse



WIRING DIAGRAM

B441660E11
0.208,1.813 1.833,2.177 1.625,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.219,1.635 0.531,1.833 0.313,0.198 10 false MB 2.219,1.333 2.531,1.531 0.313,0.198 10 false 3D 2.208,1.469 3.844,1.813 1.635,0.344 10 false Instrument Panel Junction Block Assembly 4.25,1.938 6.167,2.344 1.917,0.406 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 4.26,1.781 4.573,1.979 0.313,0.198 10 false O10 5.677,0.75 6.906,0.948 1.229,0.198 10 false S/ROOF 6.417,0.625 7.156,1.219 0.74,0.594 10 false from Auxiliary Battery 5.177,1.458 5.74,1.656 0.563,0.198 10 false GND 5.552,1.333 6.115,1.531 0.563,0.198 10 false 2 5.344,0.615 5.906,0.813 0.563,0.198 10 false B 5.552,0.49 6.115,0.688 0.563,0.198 10 false 1 4.583,0.75 5.146,0.948 0.563,0.198 10 false LIN1 4.406,0.594 4.969,0.792 0.563,0.198 10 false 7 2.979,0.604 3.542,0.802 0.563,0.198 10 false 17 1.948,0.615 2.51,0.813 0.563,0.198 10 false 16 1.583,0.76 2.146,0.958 0.563,0.198 10 false LIN2 0.719,2.49 2.76,2.729 2.042,0.24 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B426690C01
2.25,1 2.583,1.25 0.333,0.25 5.583,0.833 5.917,1.083 0.333,0.25 2.25,2.083 2.25,1.583 false 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.313,1.052 2.625,1.25 0.313,0.198 10 false MB 5.677,0.885 5.99,1.083 0.313,0.198 10 false 3D 2.135,2.135 2.448,2.333 0.313,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3D-17 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))
a.

Disconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
3D-17 - O10-7 (MPX1) Power switch off Below 1 Ω
O10-7 (MPX1) or 3D-17 - Body ground Power switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - AUXILIARY BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O10-1 (B) - O10-2 (E) Power Switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O10-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Replace the sliding roof ECU (sliding roof drive gear sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1273 is not output.



Result:
Proceed to
OK
NG



OK

END (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)