Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1656/38  Seat Belt Buckle Switch LH Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the airbag ECU assembly and seat belt buckle switch LH (front seat inner belt assembly LH).

DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the seat belt buckle switch LH circuit.

·

Seat belt buckle switch LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Seat belt buckle switch LH (Front seat inner belt assembly LH)

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

C239223E35
1.667,0.76 2.375,1.365 0.708,0.604 10 false LBE+ 1.688,2.198 2.365,2.677 0.677,0.479 10 false LBE- 5.406,0.896 5.833,1.333 0.427,0.438 10 false LBE+ 5.406,2.073 5.865,2.5 0.458,0.427 10 false LBE- 2.115,0.802 2.479,1.26 0.365,0.458 10 false 2 2.115,1.958 2.448,2.375 0.333,0.417 10 false 1 5.135,0.802 5.51,1.333 0.375,0.531 10 false 10 5.135,1.958 5.448,2.365 0.313,0.406 10 false 18 0.552,2.917 1.365,3.302 0.813,0.385 10 false M72 0.552,3.073 2.688,3.625 2.135,0.552 10 false Seat Belt Buckle Switch LH (Front Seat Inner Belt Assembly LH) 5.323,2.906 5.74,3.344 0.417,0.438 10 false M1 5.323,3.073 6.896,3.479 1.573,0.406 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and front seat inner belt assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and front seat inner belt assembly LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
C265017C06
0.385,3.604 0.74,3.833 0.354,0.229 1.135,0.531 1.458,0.76 0.323,0.229 0.917,4.25 1.292,3.75 false 1.917,4.25 1.521,3.75 false 1.531,2.094 1.531,1.677 1.531,1.677 1.365,1.677 false 2.073,0.802 1.823,0.802 false 2,0.333 2.396,0.677 false 2,1.25 2.396,0.896 false 0.583,2.052 0.938,2.396 0.354,0.344 10 false *1 2.521,2.396 2.854,2.708 0.333,0.313 10 false *2 1.208,1.604 1.594,1.948 0.385,0.344 10 false *3 1.677,0.729 2.021,1.031 0.344,0.302 10 false *4 0.938,0.146 1.292,0.49 0.354,0.344 10 false *a 0.198,3.167 0.521,3.5 0.323,0.333 10 false *b 2.021,2.083 2.354,2.396 0.333,0.313 10 false A 1.729,2.083 2.063,2.396 0.333,0.313 10 false B 1.271,2.083 1.604,2.396 0.333,0.313 10 false C 0.969,2.083 1.302,2.396 0.333,0.313 10 false D 1.208,0.563 1.542,0.875 0.333,0.313 10 false M1 0.438,3.635 0.771,3.948 0.333,0.313 10 false M72 1.615,0.25 2.042,0.458 0.427,0.208 10 false LBE+ 1.646,1.177 2.073,1.385 0.427,0.208 10 false LBE- 1.771,4.25 2.302,4.5 0.531,0.25 10 false LBE+ 0.76,4.25 1.167,4.479 0.406,0.229 10 false LBE-
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M72-2 (LBE+) - M72-1 (LBE-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
C283378C07
0.792,2.156 1.167,2.396 0.375,0.24 1.521,0.948 1.521,0.615 false 1.229,2.708 1.708,2.271 false 2.354,2.698 1.885,2.271 false 0.354,0.448 0.688,0.771 0.333,0.323 10 false *1 2.719,0.781 3.031,1.115 0.313,0.333 10 false *2 1.469,0.969 1.802,1.24 0.333,0.271 10 false *3 0.542,1.615 0.833,1.979 0.292,0.365 10 false *a 2.271,0.448 2.583,0.781 0.313,0.333 10 false A 1.875,0.448 2.188,0.781 0.313,0.333 10 false B 1.094,0.448 1.406,0.781 0.313,0.333 10 false C 0.698,0.448 1.01,0.781 0.313,0.333 10 false D 1.094,2.719 1.49,2.938 0.396,0.219 10 false LBE- 2.24,2.708 2.635,2.927 0.396,0.219 10 false LBE+ 0.854,2.198 1.25,2.417 0.396,0.219 10 false M72
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M72-2 (LBE+) - M72-1 (LBE-) Always 1 MΩ or higher



Result:
Result
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
C283378C07
0.792,2.156 1.167,2.396 0.375,0.24 1.521,0.948 1.521,0.615 false 1.229,2.708 1.708,2.271 false 2.354,2.698 1.885,2.271 false 0.354,0.448 0.688,0.771 0.333,0.323 10 false *1 2.719,0.781 3.031,1.115 0.313,0.333 10 false *2 1.469,0.969 1.802,1.24 0.333,0.271 10 false *3 0.542,1.615 0.833,1.979 0.292,0.365 10 false *a 2.271,0.448 2.583,0.781 0.313,0.333 10 false A 1.875,0.448 2.188,0.781 0.313,0.333 10 false B 1.094,0.448 1.406,0.781 0.313,0.333 10 false C 0.698,0.448 1.01,0.781 0.313,0.333 10 false D 1.094,2.719 1.49,2.938 0.396,0.219 10 false LBE- 2.24,2.708 2.635,2.927 0.396,0.219 10 false LBE+ 0.854,2.198 1.25,2.417 0.396,0.219 10 false M72
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M72-2 (LBE+) - Body ground Power switch on (IG) Below 1 V
M72-1 (LBE-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C283378C07
0.792,2.156 1.167,2.396 0.375,0.24 1.521,0.948 1.521,0.615 false 1.229,2.708 1.708,2.271 false 2.354,2.698 1.885,2.271 false 0.354,0.448 0.688,0.771 0.333,0.323 10 false *1 2.719,0.781 3.031,1.115 0.313,0.333 10 false *2 1.469,0.969 1.802,1.24 0.333,0.271 10 false *3 0.542,1.615 0.833,1.979 0.292,0.365 10 false *a 2.271,0.448 2.583,0.781 0.313,0.333 10 false A 1.875,0.448 2.188,0.781 0.313,0.333 10 false B 1.094,0.448 1.406,0.781 0.313,0.333 10 false C 0.698,0.448 1.01,0.781 0.313,0.333 10 false D 1.094,2.719 1.49,2.938 0.396,0.219 10 false LBE- 2.24,2.708 2.635,2.927 0.396,0.219 10 false LBE+ 0.854,2.198 1.25,2.417 0.396,0.219 10 false M72
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M72-2 (LBE+) - Body ground Always 1 MΩ or higher
M72-1 (LBE-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPLACE FLOOR WIRE

6.CHECK DTC
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly


Connect the connectors to the airbag ECU assembly and front seat inner belt assembly LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1656/38 is not output.


HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag ECU Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Replace the front seat inner belt assembly LH with a known good one.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1656/38 is not output.


HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Restore the front seat inner belt assembly LH that was installed for testing to its original location.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG