Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B162B/85  Side Airbag Sensor Assembly No.2 Lost Communication (RH)  B162C/85  Side Airbag Sensor Assembly No.2 Initialization Error (RH)  


DESCRIPTION

The side collision sensor RH circuit (bus 2) consists of the airbag ECU assembly and side No. 2 airbag sensor assembly RH.

The side No. 2 airbag sensor assembly RH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B162B/85 Side Airbag Sensor Assembly No.2 Lost Communication (RH)
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Side No. 2 airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode
B162C/85 Side Airbag Sensor Assembly No.2 Initialization Error (RH)
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Side No. 2 airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

C303969E19
5.323,2.885 6.969,3.531 1.646,0.646 10 false Airbag ECU Assembly 5.323,2.719 6.885,3.198 1.563,0.479 10 false M45 5.135,0.802 5.854,1.198 0.719,0.396 10 false 20 5.135,1.771 5.854,2.167 0.719,0.396 10 false 19 5.375,0.906 6.094,1.302 0.719,0.396 10 false BCR+ 5.375,1.875 6.094,2.271 0.719,0.396 10 false BCR- 1.406,0.906 2.125,1.302 0.719,0.396 10 false BFR+ 1.427,1.875 2.146,2.271 0.719,0.396 10 false BFR- 1.844,0.802 2.563,1.198 0.719,0.396 10 false 2 1.844,1.781 2.563,2.177 0.719,0.396 10 false 1 0.563,2.719 2.125,3.333 1.563,0.615 10 false M28 0.563,2.885 3.115,3.188 2.552,0.302 10 false Side No. 2 Airbag Sensor Assembly RH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
C341895C03
0.833,0.5 1.25,0.75 0.417,0.25 0.583,3.583 1,3.833 0.417,0.25 1.625,2.521 1.625,1.938 1.625,1.938 1.375,1.938 false 1.833,1.375 1.833,1.167 false 1.458,1.24 1.771,0.875 false 2.208,1.229 1.896,0.875 false 1.052,4.229 1.406,3.729 false 2.01,4.24 1.688,3.729 false 0.667,2.5 1.094,2.896 0.427,0.396 10 false *1 2.552,2.229 2.979,2.781 0.427,0.552 10 false *2 1.219,1.865 1.698,2.281 0.479,0.417 10 false *3 1.771,1.406 2.104,1.74 0.333,0.333 10 false *4 0.688,0.177 1.073,0.458 0.385,0.281 10 false *a 0.427,3.25 0.833,3.76 0.406,0.51 10 false *b 2.083,1.25 2.583,1.594 0.5,0.344 10 false BCR+ 1.292,1.25 1.792,1.594 0.5,0.344 10 false BCR- 0.917,0.542 1.417,0.885 0.5,0.344 10 false M45 2.188,2.5 2.615,3.052 0.427,0.552 10 false A 1.885,2.5 2.313,3.052 0.427,0.552 10 false B 1.292,2.5 1.719,3.052 0.427,0.552 10 false C 0.979,2.5 1.406,3.052 0.427,0.552 10 false D 0.667,3.625 1.167,3.969 0.5,0.344 10 false M28 1.875,4.25 2.375,4.594 0.5,0.344 10 false BFR+ 0.906,4.25 1.406,4.594 0.5,0.344 10 false BFR-
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Using a service wire, connect terminals 20 (BCR+) and 19 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-2 (BFR+) - M28-1 (BFR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
C341628C03
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 false 2.104,2.813 1.719,2.375 false 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.25,2.708 0.583,0.417 10 false M28 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-2 (BFR+) - M28-1 (BFR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
C341628C03
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 false 2.104,2.813 1.719,2.375 false 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.25,2.708 0.583,0.417 10 false M28 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch off.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M28-2 (BFR+) - Body ground Power switch on (IG) Below 1 V
M28-1 (BFR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C341628C03
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 false 2.104,2.813 1.719,2.375 false 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.25,2.708 0.583,0.417 10 false M28 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-2 (BFR+) - Body ground Always 1 MΩ or higher
M28-1 (BFR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

6.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly


Connect the connector to the airbag ECU assembly.


b.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B162B/85, B162C/85, B163B/86 and B163C/86 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B162B/85 or B162C/85 is output. A
DTC B163B/86 or B163C/86 is output. B
DTCs B162B/85, B162C/85, B163B/86 and B163C/86 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C