Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B163B/86  Side Airbag Sensor Assembly No.2 Lost Communication (LH)  B163C/86  Side Airbag Sensor Assembly No.2 Initialization Error (LH)  


DESCRIPTION

The side collision sensor LH circuit (bus 2) consists of the airbag ECU assembly and side No. 2 airbag sensor assembly LH.

The side No. 2 airbag sensor assembly LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 2).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B163B/86 Side Airbag Sensor Assembly No.2 Lost Communication (LH)
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 2).

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Side No. 2 airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode
B163C/86 Side Airbag Sensor Assembly No.2 Initialization Error (LH)
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 2).

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Side No. 2 airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

C303969E20
5.302,2.885 6.948,3.531 1.646,0.646 10 false Airbag ECU Assembly 5.302,2.719 6.865,3.198 1.563,0.479 10 false M1 5.135,0.802 5.854,1.198 0.719,0.396 10 false 21 5.135,1.771 5.854,2.167 0.719,0.396 10 false 22 5.375,0.906 6.094,1.302 0.719,0.396 10 false BCL+ 5.375,1.875 6.094,2.271 0.719,0.396 10 false BCL- 1.417,0.906 2.135,1.302 0.719,0.396 10 false BFL+ 1.438,1.875 2.156,2.271 0.719,0.396 10 false BFL- 1.844,0.802 2.563,1.198 0.719,0.396 10 false 2 1.844,1.781 2.563,2.177 0.719,0.396 10 false 1 0.563,2.719 2.125,3.333 1.563,0.615 10 false M29 0.552,2.885 3.219,3.229 2.667,0.344 10 false Side No. 2 Airbag Sensor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
C341627C03
0.854,0.51 1.229,0.76 0.375,0.25 0.583,3.583 1,3.833 0.417,0.25 1.635,2.531 1.635,2.198 false 2.01,1.396 2.01,1.188 false 1.635,1.24 1.948,0.885 false 2.365,1.24 2.063,0.885 false 1.083,4.229 1.406,3.74 false 2.052,4.229 1.688,3.74 false 0.667,2.052 1.042,2.302 0.375,0.25 10 false *1 2.573,2.354 2.979,2.938 0.406,0.583 10 false *2 1.573,2.552 1.927,2.865 0.354,0.313 10 false *3 1.948,1.406 2.281,1.646 0.333,0.24 10 false *4 0.698,0.188 1.052,0.51 0.354,0.323 10 false *a 0.406,3.24 0.771,3.604 0.365,0.365 10 false *b 2.188,2.063 2.594,2.646 0.406,0.583 10 false A 1.885,2.063 2.292,2.646 0.406,0.583 10 false B 1.292,2.063 1.698,2.646 0.406,0.583 10 false C 0.979,2.063 1.385,2.646 0.406,0.583 10 false D 1.479,1.25 1.917,1.583 0.438,0.333 10 false BCL+ 2.24,1.25 2.677,1.583 0.438,0.333 10 false BCL- 0.958,0.552 1.396,0.885 0.438,0.333 10 false M1 0.667,3.625 1.104,3.958 0.438,0.333 10 false M29 1.927,4.25 2.365,4.583 0.438,0.333 10 false BFL+ 0.938,4.25 1.375,4.583 0.438,0.333 10 false BFL-
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Using a service wire, connect terminals 21 (BCL+) and 22 (BCL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M29-2 (BFL+) - M29-1 (BFL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
C341629C03
0.583,2.167 1,2.417 0.417,0.25 1.646,1.188 1.646,0.771 false 1.125,2.823 1.427,2.313 false 2.01,2.823 1.708,2.313 false 0.688,0.615 1.063,0.938 0.375,0.323 10 false *1 2.594,0.896 2.99,1.25 0.396,0.354 10 false *2 1.583,1.208 1.969,1.5 0.385,0.292 10 false *3 0.417,1.792 0.833,2.365 0.417,0.573 10 false *a 2.208,0.625 2.604,0.979 0.396,0.354 10 false A 1.896,0.625 2.292,0.979 0.396,0.354 10 false B 1.313,0.625 1.708,0.979 0.396,0.354 10 false C 1,0.625 1.396,0.979 0.396,0.354 10 false D 0.667,2.208 1.083,2.781 0.417,0.573 10 false M29 0.99,2.833 1.406,3.167 0.417,0.333 10 false BFL- 1.885,2.833 2.302,3.167 0.417,0.333 10 false BFL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M29-2 (BFL+) - M29-1 (BFL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
C341629C03
0.583,2.167 1,2.417 0.417,0.25 1.646,1.188 1.646,0.771 false 1.125,2.823 1.427,2.313 false 2.01,2.823 1.708,2.313 false 0.688,0.615 1.063,0.938 0.375,0.323 10 false *1 2.594,0.896 2.99,1.25 0.396,0.354 10 false *2 1.583,1.208 1.969,1.5 0.385,0.292 10 false *3 0.417,1.792 0.833,2.365 0.417,0.573 10 false *a 2.208,0.625 2.604,0.979 0.396,0.354 10 false A 1.896,0.625 2.292,0.979 0.396,0.354 10 false B 1.313,0.625 1.708,0.979 0.396,0.354 10 false C 1,0.625 1.396,0.979 0.396,0.354 10 false D 0.667,2.208 1.083,2.781 0.417,0.573 10 false M29 0.99,2.833 1.406,3.167 0.417,0.333 10 false BFL- 1.885,2.833 2.302,3.167 0.417,0.333 10 false BFL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M29-2 (BFL+) - Body ground Power switch on (IG) Below 1 V
M29-1 (BFL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C341629C03
0.583,2.167 1,2.417 0.417,0.25 1.646,1.188 1.646,0.771 false 1.125,2.823 1.427,2.313 false 2.01,2.823 1.708,2.313 false 0.688,0.615 1.063,0.938 0.375,0.323 10 false *1 2.594,0.896 2.99,1.25 0.396,0.354 10 false *2 1.583,1.208 1.969,1.5 0.385,0.292 10 false *3 0.417,1.792 0.833,2.365 0.417,0.573 10 false *a 2.208,0.625 2.604,0.979 0.396,0.354 10 false A 1.896,0.625 2.292,0.979 0.396,0.354 10 false B 1.313,0.625 1.708,0.979 0.396,0.354 10 false C 1,0.625 1.396,0.979 0.396,0.354 10 false D 0.667,2.208 1.083,2.781 0.417,0.573 10 false M29 0.99,2.833 1.406,3.167 0.417,0.333 10 false BFL- 1.885,2.833 2.302,3.167 0.417,0.333 10 false BFL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M29-2 (BFL+) - Body ground Always 1 MΩ or higher
M29-1 (BFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

6.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Connect the connector to the airbag ECU assembly.


b.

Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B162B/85, B162C/85, B163B/86 and B163C/86 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B163B/86 or B163C/86 is output. A
DTC B162B/85 or B162C/85 is output. B
DTCs B162B/85, B162C/85, B163B/86 and B163C/86 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C